Search:

Type: Posts; User: Btroy

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    2,305

    53 Willys PU turn signal issue

    Hi guys I'm back and needing a little help on this turn signal issue.
    Problem I am having is I can't get the turn signals to flash. I followed the wiring on the new signal unit but no matter if I...
  2. Replies
    6
    Views
    6,101

    Nice send me a PM with what you are asking for...

    Nice send me a PM with what you are asking for them.
  3. Replies
    6
    Views
    6,101

    Thanks for the info and pics. I sure don't want...

    Thanks for the info and pics. I sure don't want to install round gauges unless absolutly needed.

    I see you live in Ft Wayne, I grew up in Anderson.
  4. Replies
    17
    Views
    15,038

    Now thats funny ....I did that already as I put...

    Now thats funny ....I did that already as I put that last diagram up somewhere and now I can't find it. I hear Ya! :)

    3594
    3595

    Thanks again.
  5. Replies
    6
    Views
    6,101

    53 Willys gauges help?

    Hi guys, I am wanting to retain the origanal gauges in my 53 Willys truck, I have looked the inter-web high and low and have not seen where I might get replacement gauges of this type. If there is...
  6. Replies
    7
    Views
    6,939

    Nice truck, looks like mine. Same color and all....

    Nice truck, looks like mine. Same color and all. I have the 4 cylinder and converted to 12v, this was because it set outside with the hood open for who knows how long before I bought it.

    When you...
  7. Replies
    17
    Views
    15,038

    Update as I hate to leave threads unanswered. ...

    Update as I hate to leave threads unanswered.

    Success finally..:)

    I was able to get my 53 running after a complete refresh and conversion.

    I followed the wiring diagram but not sure if I...
  8. Replies
    17
    Views
    15,038

    Thanks for the diagrams, I am pretty sure its...

    Thanks for the diagrams, I am pretty sure its wired correctly as I followed the new wiring diagram I got with the hasness, I will verify once again.

    Thanks for your time really appreciate this.
  9. Replies
    17
    Views
    15,038

    Can someone tell me the minimum wires I need to...

    Can someone tell me the minimum wires I need to start the engine?

    Wondering if the plug wires are correct as I whitched to 12 volt system.

    Currently I only have the negative side of the coil...
  10. Replies
    2
    Views
    4,473

    Mines a 53 but here are some pics. Top pivots...

    Mines a 53 but here are some pics. Top pivots from bottom up, bottom pivots from front up. So to access below seat you lift back then lift bottom. Back will rest on bottom to keep it up.
    At least...
  11. Replies
    17
    Views
    15,038

    That has changed, I went ahead and bought a...

    That has changed, I went ahead and bought a distributor from our host with the electronics
    In it.

    It appears I maybe burning up
    The coils. Now when I test the secondary
    It is showing 9.9 on...
  12. Replies
    17
    Views
    15,038

    Ok new coil and I get spark with it as in...

    Ok new coil and I get spark with it as in drawing.
    But when I connect up the wires
    It cranks but no fire from the coil tower now?
  13. Replies
    17
    Views
    15,038

    Ok looks like the new coil is bad, as from + to -...

    Ok looks like the new coil is bad, as from + to - it measures 03.4. From center to - my meter does not move.

    I will get another coil.

    Thanks for your assistance. Will reply once I get another...
  14. Replies
    17
    Views
    15,038

    I went ahead and bought a new electronic...

    I went ahead and bought a new electronic distributor from our host. I am still not getting any spark.
    I have a flame thrower coil. The instructions say it has to be an internal resistor type or I...
  15. Replies
    17
    Views
    15,038

    Cap was removed and rotor is turning CCW as...

    Cap was removed and rotor is turning CCW as expected.

    Also measured voltage on negitive side of coil while cranking and it is thwe same as the postive side 9-8 volts.
  16. Replies
    17
    Views
    15,038

    No spark after 12 volt conversion

    Hi guys I'm back on my 53 Willys truck project.
    Got the motor back together and have fuel but no spark. I converted to a pertronix but can't figure out why I'm not getting any spark.

    With the...
  17. Replies
    8
    Views
    41,137

    Still working on this but have an issue when...

    Still working on this but have an issue when cranking, if I go from ground to the positive side of coil I see 12v while cranking. If I measure between the pos and negative post on the coil I get 0...
  18. Replies
    8
    Views
    41,137

    There is a problem with that, there is noway to...

    There is a problem with that, there is noway to keep the vacuum advanced installed as there is no provision to connet the vacuum pod to the points plate that was removed. I will try it without and...
  19. Replies
    8
    Views
    41,137

    Electronic ing conversion ?

    Hi guys, back again. I attempted to fire up my 53 after I renewed it. Points were replaced but the wires burnt. I want to convert to pertronix but my dist has a vacuum advance. Do I eliminate that as...
  20. Replies
    3
    Views
    29,442

    Ok thanks for the explanation. It was my...

    Ok thanks for the explanation. It was my understanding it used to be a forestry service truck then went to a fire department. Could have been added at that point. Appreciate your input.
  21. Replies
    3
    Views
    29,442

    Dash panel identification...help

    Working on my 53 truck and I have a dash panel directly in front of the steering wheel. Can I get some help identifying what this
  22. Replies
    2
    Views
    22,014

    Ok thanks for the info.

    Ok thanks for the info.
  23. Replies
    2
    Views
    22,014

    6v to 12v voltage regulator ?

    Hi guys, I'm making progress on my 53 truck, have the engine rebuilt converting to 12v. I bought a 12v regulator along with my new wiring hardness. Will have to splice the battery wire so it will...
  24. Thread: New to 53 Willys

    by Btroy
    Replies
    4
    Views
    5,628

    2158 One side. I have received that catalog,...

    2158
    One side.
    I have received that catalog, it's great.

    Thanks
  25. Thread: New to 53 Willys

    by Btroy
    Replies
    4
    Views
    5,628

    2159 Picture of outside

    2159
    Picture of outside
Results 1 to 25 of 26
Page 1 of 2 1 2