Page 3 of 3 FirstFirst 123
Results 21 to 27 of 27

Thread: New guy - Have a lot to learn

  1. #21
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    1,406
    I often do that if I run out of gas.... Or at least I did before fixing the fuel gage.

  2. #22
    Junior Member
    Join Date
    Apr 2019
    Posts
    9
    I'll give it a try next time it's having troubles starting after sitting. I got it out a little bit tonight and it started fairly easily. The starter is turning really slow to the point it stops and then it fires up.

    Here's a couple more pictures of it if anyone's interested. Sorry for the one sideways picture.

    As for seats - the seats in it have the sliding rails under them. If I got some regular low back seats for it would they bolt right onto the existing bases? Do you think they would still sit too high?
    Attached Images Attached Images
    Last edited by CMT-1109; 04-16-2019 at 06:20 PM.

  3. #23
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    1,406
    The body is really clean! We like pictures around here, so show off as you please.
    The original seat frames are a fixed position, one size fits most design. From what I can see, you can expect around a three inch drop in your driving position. The seat frame bridges the fuel tank, and mounts to the floor up front, and on the floor behind the tank. The seat tracks you have currently would have to be removed. The passenger seat mounts with two pivot pints on the front edge of the tool compartment.
    As far as the starter, I would check the battery voltage draw. The battery may be getting weak, or the voltage regulator may need a little tweaking.

  4. #24
    Junior Member
    Join Date
    Apr 2019
    Posts
    9
    I've seen plenty of pictures of original seats but the frames are a little tough to come by and I'm not in the position to drop 6-800 on seats and cushions right now. When I drive it now, my head sticks out the top so I would definitely benefit from lower seats and seats that don't crowd the steering wheel so bad.

    It's an 8 volt battery and I've checked it before and after starting it and it checks at 8v. The regulator pushes it to 8.4ish volts under throttle. Also, I keep it on a tender when it's not being driven. It might just require some cleaning up contacts and grounds. I'm not used to older vehicles but it seems to turn very slowly.

    Thanks for the comments! My 5 year old step daughter absolutely loves it and asks to play in the Jeep and go for rides every day. She brings her random stuffed animals and waves to everyone we drive by. Haha

  5. #25
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    1,406
    I was having a brain fade upon talking about the battery. You had already covered what voltage you had. A six or eight volt do turn the engine much slower than you would se on a 12 volt system. The 6 volt does supply a considerable more amount of torque.

    When we purchased our 2A, it had bits of the original seat frames. I came across a set that were in tough shape. The legs were rusted out, so I found some pipe that matched. A little cutting and welding in and they are good to go. I found some boat cushions that looked and fit just right. We have been on the hunt for an original rear seat, so we can take the grand kids around. I ran across this add on ewillys this morning; http://www.ewillys.com/2019/04/17/fr...incoln-ca-200/
    Attached Images Attached Images
    Last edited by gmwillys; 04-17-2019 at 06:04 AM.

  6. #26
    Super Moderator LarrBeard's Avatar
    Join Date
    Nov 2014
    Location
    Ft. Wayne, IN
    Posts
    865

    Balky Starters, Kids and Grandkids

    "The starter is turning really slow to the point it stops and then it fires up."

    If the battery is charging to 8.4 volts at cruise, that's probably a sign that the regulator has been reset. I'd look at the battery voltage while it's cranking. The stopping just before it fires up and slow cranking make me wonder if there's not an issue with the battery or starter - and I'd guess battery first.

    The starter spec for the Autolite MZ-4113 says that the stall current is 420-amps at 3-volts. If the starter is stalling and the voltage is 4 or 4.5 volts, I'd guess a starter problem. Check brushes and bearings. If it drops below 3-volts, I'd guess battery. I am assuming you have good battery cables - auto store 12-volt cables are marginal on 6 volt systems.

    A rare possibility is a timing issue, it could be firing early on the compression stroke and stalling the starter just as it starts - but since it cranks slowly all the time - probably not.

    My step-grand-daughter thinks the '48 is neat - but she doesn't want to drive it. You know you've made a hit when the grand-daughter wants your truck as part of her senior picture portfolio. Her brother will drive it on occasion. My youngest daughter (42 years old) is a pest - she wants to take it out and drive every time she comes to visit.
    Attached Images Attached Images

  7. #27
    Member bmorgil's Avatar
    Join Date
    Dec 2018
    Location
    Northwestern Ohio
    Posts
    73
    The youngest is right on the money! Pester away!

    An 8 volt system. Until this forum I never knew there was such a thing.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •