Register
Help
Remember Me?
What's New?
Activity Stream
New Posts
New Events
Mark Forums Read
Forum
Advanced Search
Home
Activity Stream
If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You may have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Activity Stream
Filter
Sort By
Time
Show
Recent
Recent
Popular
Popular
Anytime
Anytime
Last 24 Hours
Last 24 Hours
Last 7 Days
Last 7 Days
Last 30 Days
Last 30 Days
All
All
Photos
Photos
Forum
Forums
Filter by:
Popular
Last 24 Hours
Clear All
New Activity (
)
Please reload this page to view the 200+ new activity items that have been created.
Older Activity
Today,
10:47 AM
davide
replied to a thread
Hot mess, a 1967 CJ-5 restoration
in
Willys Restoration Projects
Thanks Bob. Clever, efficient and inexpensive. FYI, the front axle u-joints went together nicely last year. Thanks for your insight on that too.
see more
48 replies | 15796 view(s)
Today,
06:13 AM
bmorgil
replied to a thread
A funny story, and then I need help.
in
Willys Jeeps - General Discussion
VT just make sure you have free play at the pedal. About 1" at the pedal is plenty. Free play is the distance between the throw out bearing and the...
see more
6 replies | 137 view(s)
Today,
06:01 AM
bmorgil
replied to a thread
Hot mess, a 1967 CJ-5 restoration
in
Willys Restoration Projects
An X sized socket will work. You can make your own tool with 2 sockets and/or washers and a piece of all-thread and two nuts. You need to be sure the...
see more
48 replies | 15796 view(s)
Yesterday,
07:44 PM
Wulfie
replied to a thread
Wulfies nostalgia project
in
Willys Restoration Projects
Im gonna fit fenders up to cj3b frame. Gonna have to remove a lil material from left fender where it interfears with shock mount. First pic shows...
see more
20 replies | 831 view(s)
Yesterday,
07:30 PM
davide
replied to a thread
Hot mess, a 1967 CJ-5 restoration
in
Willys Restoration Projects
Well, Winter is over and I'm back to working on the CJ again without my hands going numb in fifteen minutes. I have everything striped and clean on...
see more
48 replies | 15796 view(s)
Yesterday,
07:05 PM
VTWilly
replied to a thread
A funny story, and then I need help.
in
Willys Jeeps - General Discussion
And..... now I broke the Upper clutch control/adjusting rod. ARGH! it completely snapped in half about 10 minuets from the house. So, now that I...
see more
6 replies | 137 view(s)
Yesterday,
06:48 PM
bmorgil
replied to a thread
63 Willys Wagon refresh
in
Willys Restoration Projects
Hopefully the lesson was well learned! The flying isn't bad, the landing is usually rough.
see more
113 replies | 65095 view(s)
Yesterday,
04:48 PM
gmwillys
replied to a thread
63 Willys Wagon refresh
in
Willys Restoration Projects
The fix wasn't too bad. A new core support, radiator, A/C condenser with lines, a stub harness, and a bumper. The drivers side uni-body stub had a...
see more
113 replies | 65095 view(s)
Yesterday,
04:37 PM
gmwillys
replied to a thread
63 Willys Wagon refresh
in
Willys Restoration Projects
That was about the same set up with her. The good thing is that it was a fairly easy fix. To be perfectly honest, I believe that she was messing...
see more
113 replies | 65095 view(s)
Yesterday,
03:21 PM
51 CJ3
replied to a thread
63 Willys Wagon refresh
in
Willys Restoration Projects
I had a niece do something similar on her way to school one morning. She swears she wasn’t on her phone. The tracks (gravel road) looked like she...
see more
113 replies | 65095 view(s)
Yesterday,
01:13 PM
LarrBeard
replied to a thread
63 Willys Wagon refresh
in
Willys Restoration Projects
Phone? Or will the truth ever be known?
see more
113 replies | 65095 view(s)
More Activity
No More Results
No Recent Activity