PDA

View Full Version : Vin location



Albynsw
11-29-2016, 02:15 AM
Hi there, I am new to the forum and have my first Jeep

I have a 1949 Overlander truck that I am getting ready to register.
I am having trouble finding a Vin number on the chassis, can anyone advise where they are located?

Thank you

Rondo
11-29-2016, 10:11 PM
Do you have a plate on the firewall near the steering column ?

Albynsw
11-30-2016, 02:25 AM
I don't think so but will check again.
The truck is at the mechanics workshop so will drop past and check

Rondo
11-30-2016, 09:22 PM
Mine is a 47 and there is a data plate there..
Are you registering for antique classic or collector
plates ?

Albynsw
12-01-2016, 12:59 AM
Thanks Rondo
I just rang my mechanic to have a look in that location
I am in Australia and I can get collector plates but have opted for standard rego as it is less complicated but a bit more expensive.
My Willy was an Australian delivered RHD model from new

Albynsw
12-01-2016, 01:15 AM
Here are a couple of pics of here

1379
1383
1381

LarrBeard
12-01-2016, 02:24 PM
The LHD '47 and '48 trucks had a nameplate on the fire wall just above the steering column. I don't know if the plate stayed there for the RHD trucks or if it moved to the other side. There have been largely unsubstantiated reports that serial numbers were stamped on the frame or in obscure places in the cab - but we checked all of the rumors and found no mystery numbers.

We really suspect that it didn't get a VIN or serial number until someone screwed the plate on. On my truck, which is clearly a '48 (e.g two-piece front seat, cloth headliner) - the serial number says it should be a '49. Someone in Toledo reached into the wrong box that summer day in late 1948!

As we restored the '48, folks marveled at the provisions for RHD modifications; the brake and clutch hangers, mounting holes for master cylinder, cutouts and stampings in the floorboard and firewall, the instruments in the mid-dash - even the hole for the RHD ignition key!

Rondo
12-01-2016, 06:15 PM
That is a nice truck !

Albynsw
12-02-2016, 01:47 AM
Thanks for the reply Larrbeard, if I can't find a plate there I will apply to the authorities for a new number

Thanks for the compliment Rondo. The truck in general is in good condition but I don't intend on restoring her to showroom condition, I like it to look a bit like a working truck and daily driver
Will use it to run into town for groceries etc
They are a beautiful looking vehicle

Rondo
12-03-2016, 11:08 AM
They sure are here is a few of mine13901391139213931394

Rondo
12-03-2016, 11:52 AM
Larrbeard, not to get of topic but did you have the
headliner custom made or did you buy it somewhere?
there are some interior items like that I could use some
direction with

Albynsw
12-05-2016, 03:16 AM
Yours looks sweet too Rondo, what is that compartment under your seat? Is that standard or you just made it up?

I don't have a headliner either so will be interested to find out more

Rondo
12-05-2016, 08:12 PM
Thanks Albynsw and yes the compartment is standard
There is one on each side under the seat. This truck was
an original stake bed and man did I have a hard time finding
parts through the last few years of restoration but I'm close now
and getting ready to roll the next one into the garage this winter

Rondo
12-10-2016, 04:27 PM
Albynsw, Is your truck still a 6volt system?

Albynsw
12-11-2016, 02:05 PM
No it is 12 volt
I have an old Ford 250hp crossflow fitted to mine