Search:

Type: Posts; User: bmorgil

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    37
    Views
    5,768

    David, as I mentioned below, the gear sets are...

    David, as I mentioned below, the gear sets are "Matched". The A1511 only Correctly matches up to the A-5707. A mismatch usually ends up putting metal shavings in the case when the gear teeth wear...
  2. Replies
    13
    Views
    506

    Everything you need in the Tech Section Scott!...

    Everything you need in the Tech Section Scott! Definitely a subject that comes up all the time. Never use 140 AXLE gear oil no matter what you read or hear. The original specification was for 140...
  3. Looking very good jb! I like the 4BT idea. My son...

    Looking very good jb! I like the 4BT idea. My son recently slipped one with compound turbos into a 4 door Square Body GMC. A lot of torque there. I cant wait to watch it grow!
  4. Replies
    13
    Views
    370

    That looks very cool! Fits right on there.

    That looks very cool! Fits right on there.
  5. Replies
    37
    Views
    5,768

    The 3.73 ratio is not listed in my chart. That...

    The 3.73 ratio is not listed in my chart. That wont matter much unless you are using stock diameter tires. 31 tall tires are going to match up pretty well with the 3.53 ratio gears. To get it perfect...
  6. Replies
    37
    Views
    5,768

    I have an old Stewart Warner chart that shows the...

    I have an old Stewart Warner chart that shows the Stewart Warner 448856 is 16 teeth and was for the 4.09 ratio. The 448855 is 15 teeth and is for the 3.53 ratio. These mate correctly with your drive...
  7. Replies
    37
    Views
    5,768

    I am going to say that is a model 20 case with...

    I am going to say that is a model 20 case with model 18 internals, sometimes called a "Super 18" davide. What is the axle ratio? That will tell us the speedo gear combination. You will need a 15, 16,...
  8. Replies
    37
    Views
    5,768

    A few more pictures will help. Particularly a few...

    A few more pictures will help. Particularly a few pictures that show any casting numbers on the case. The shifter mechanism looks like a 20. Though as we spoke of before, it could be a single stick...
  9. Replies
    13
    Views
    370

    Jb you may want to list it here. ...

    Jb you may want to list it here.

    https://willysforsale.com/
  10. Replies
    13
    Views
    506

    That has me smiling also Scott! Keep it on the...

    That has me smiling also Scott! Keep it on the road man, its all about remembering the past, and creating the future.
  11. Replies
    6
    Views
    229

    Good news! Just remember, leaving it in one...

    Good news! Just remember, leaving it in one position can lead to it staying in one postilion.
  12. Replies
    6
    Views
    229

    Jeff has you going in the right direction. As...

    Jeff has you going in the right direction. As things get old and worn it can get difficult to get it into gear. It sounds like things aren't quite lined up. Try putting the transmission in first and...
  13. Replies
    13
    Views
    506

    You just torque it back on. It just gets stuck on...

    You just torque it back on. It just gets stuck on there pretty good after its been on a while. The box is a simple design. Sometimes the only thing wrong with them is wear in the "High Point" the...
  14. Replies
    13
    Views
    506

    Yes Scott the pitman arm can be on the sector...

    Yes Scott the pitman arm can be on the sector shaft fairly tight. A pitman arm puller (a good strong one) might be needed. I used the KW kit. It has all you need, except the tools. It is getting hard...
  15. Replies
    87
    Views
    5,336

    Yes you can leave the transfercase/transmission...

    Yes you can leave the transfercase/transmission cross member in. The bell housing stays in and bolted to the transmission. Unbolt it from the block. Follow your process it sounds good to me! TJ is...
  16. Replies
    87
    Views
    5,336

    If you don't support the back, it could break the...

    If you don't support the back, it could break the motor mounts. Usually the block will tilt back and hit the firewall. That can smash the linkage bracket for the throttle.
  17. Replies
    7
    Views
    203

    Or ask TJones!

    Or ask TJones!
  18. Replies
    87
    Views
    5,336

    Definitely need to get it in the air high enough...

    Definitely need to get it in the air high enough to drop everything down and clear of the frame. The support for the rear of the engine needs to be suspended from the frame so you can lift the...
  19. Replies
    7
    Views
    203

    A good question for gmwillys. Come in...

    A good question for gmwillys. Come in gmwillys.... calling gmwillys. I think a CJ7 is considerably longer.
  20. Replies
    87
    Views
    5,336

    At this point t you are at the crossroad. How far...

    At this point t you are at the crossroad. How far are you going? For instance if you intend to take the body off, it is pretty easy to do anything. If the body is staying on, the transfercase and...
  21. Replies
    7
    Views
    203

    I have seen Stainless Bodies. It does pose some...

    I have seen Stainless Bodies. It does pose some interesting issues. John Delorean ended up wishing he painted them! Tough to fix when they get dented.
  22. Replies
    13
    Views
    506

    The box is a pretty straight forward rebuild. Be...

    The box is a pretty straight forward rebuild. Be sure to use the new "unitized" or one piece bearings. The bearings in the box are originally individual balls. You can also use new individual balls...
  23. I remember your post Mark, we lost everything...

    I remember your post Mark, we lost everything from the last week in Aug through the beginning of September. I remember the discussion about the general consensus on Jeep fuel gauge accuracy. It is a...
  24. Replies
    2
    Views
    350

    That's a great find Jags! Posts never end, they...

    That's a great find Jags! Posts never end, they just go to sleep every now and then!
  25. For sure keep us posted on the progress Jags,...

    For sure keep us posted on the progress Jags, There is always the easy way out on the gauges. The reproductions are very good. You have some unique stuff however.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4