Search:

Type: Posts; User: steve welder

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    1,201

    Thank you to all for the help.....I levelled the...

    Thank you to all for the help.....I levelled the jeep and than put bracket level and tacked.....Hooked up bell crank and drag link....looked good and so I welded it up.....took it out for a spin
    Its...
  2. Replies
    9
    Views
    1,201

    Thank you and thanks to all for help ASAP I will...

    Thank you and thanks to all for help
    ASAP I will get back to the Jeep. Im figuring to level the jeep and than level the bracket both ways. I know exactly were it goes on tube but its levelling it...
  3. Replies
    9
    Views
    1,201

    Thank you bmorgil !!! Im figuring the hole for...

    Thank you bmorgil !!! Im figuring the hole for the pin is in the exact same spot as the old bracket
  4. Replies
    9
    Views
    1,201

    Bell crank bracket

    Im installing a new bell crank bracket on my CJ2A..... I took measurements off the old one as far as center to center of pin and figured this would be location of new bracket
    I already removed old...
  5. Replies
    6
    Views
    1,459

    Well I bought a new radiator from Kaiser. Was...

    Well I bought a new radiator from Kaiser. Was pretty much bolt in. My upper hose was to short and I had to lengthen the radiator to firewall rod
    I want to pressure check the system but my Stant...
  6. Replies
    6
    Views
    1,459

    I think it is partially plugged....It has the fan...

    I think it is partially plugged....It has the fan shroud soldiered or brazed to it....If they need to rod it, removing and reinstalling that shroud has got to be expensive
    What would be my most...
  7. Replies
    6
    Views
    1,459

    I will look more closely at water in rad and put...

    I will look more closely at water in rad and put pressure checker and see if pressure rises. I pulled the water pump and nothing stood out as far as the impeller in pump
    No white smoke and starts...
  8. Replies
    6
    Views
    1,459

    Running to hot

    I flushed the radiator the best I could....I removed the thermostat, she still runs hot, gauge shows 180-190. thermometer in rad show 170 plus
    I would have thought it would have run cooler and...
  9. Thread: Steering

    by steve welder
    Replies
    1
    Views
    707

    Steering

    Can some play be taken out of the steering by the adjusting stud located on the side of the steering box
    Looking to buy some time before I rebuild the box
    Thanks for any help/advise
  10. Replies
    1
    Views
    709

    Engine rebuilder

    Just planning ahead. My CJ2A will get a complete teardown starting this fall or maybe earlier....The engine is already 60 over, if it need a rebore I want to sleeve it. Either way im having it...
  11. Replies
    9
    Views
    1,513

    . She is definitely running hot,...

    . She is definitely running hot, overheating......When I remove the cap I saw this copper looking sludge inside which I assume is stop leak....I see it slightly around the head gasket area.....Im...
  12. Replies
    9
    Views
    1,513

    Stalling ....maiden voyage

    I registered the 48 CJ today, took it out maybe ten miles....The last time I drove a old jeep was my dads 48 CJ2A around 1971. I was about 19, quite the experience today at 70 yrs old.....She runs...
  13. Replies
    1
    Views
    660

    Rear main seal

    The rear main seal on my 1948 CJ is leaking bad but seems a few drips while running but when I shut it down it was literally pouring down in a steady stream and then steady drips until it finally...
  14. Thread: Gettings

    by steve welder
    Replies
    3
    Views
    1,379

    Gettings

    My name is Steve and I am the proud owner of a 1948 CJ2A. Its in decent shape and needs some work to be road worthy
    My future plans are to do a body off complete restoration but for the time...
Results 1 to 14 of 14