Im trying for original if possible, but not opposed to the new style, if thats I'll I can find.
I looked at the new style. It appears to have different connection methods.......What type...
Type: Posts; User: Gizzard
Im trying for original if possible, but not opposed to the new style, if thats I'll I can find.
I looked at the new style. It appears to have different connection methods.......What type...
I’m trying to locate and buy the proper fuel pump, with no luck. I don’t have a core so it’s no dice so far
I just acquired a 24 volt starter and a 24 volt generator. They look good, but have no idea if they function.
What options do I have for sending off for rebuild?
Been busy gathering parts............lots to share soon!!
Gathering up and hunting parts is half the fun!!
Looking over the transfer case a little closer and I discover more of Bubba's fine handiwork:p
Check out this action:
8447
8448
Oh, btw, here’s a can of worms..... I read up on crank rear main seals last night till cobwebs filled my head. Rope vs best seals etc...... holy cow. Everyone has a different take on it. Hours...
...... yep, plus this will give me the excuse to buy new pistons, rods, hardware, etc.
Not sure about the cam yet. Kinda leaning towards a new cam just because. ...... machinist is gonna see...
Just talked to machine shop. We are boring both sleeves and remaining two cylinders out to 60 over.
Havent settled on a course of action. All I know now is that it has an existing sleeve at 30 in Cyl one and it will need new sleeve in cyl 2........ cyl 3 and 4 bored to 60 to remove gouge.
...
After further inspection by the machinist, it was definitely the the wrist pins migrating out that cause the gouges. Cyl 2 and 4 had matching gouges. We also discovered a odd rod out of the 4. ...
There were actually two cylinders that had matching gouges.......2 and 4
Have no idea why they failed for sure, , but the only way possible is that the wrist pin locking bolt on the rod came...
Dropped the engine block, head and crank off at the machine shop today.
8425
Looks like the wrist pins got loose on a couple of cylinders and gouged um up pretty good
8426
8427
Yes, thx for the input guys......gonna weld her. Besides that will give me a chance to try out my new rotacut bit:cool:
Question of the day: Repair or replace?
Rear spring hangers are all oblong and wallered out. (Front hangers look OK)
Weld up and re-drill? or cut the hangers off and replace including new...
Yes, I was scared away from those wheels while viewing them on the Kaiser site because of the civilian designation listed. If those are indeed a match to the original wheels then I'm onboard.
...
Original wheels were stolen before I acquired the jeep so a set of torched out misfits with may-pops were fitted to get it home.....trash now
Been on the hunt for a set......Which wheels were...
Thanks again for the info guys.
Is there one type that is better than others? Source?
'
BTW, could this be real? Lotsa miles at 40 mph;)
8389
Thanks for the replies.
Here's a closer look at the tub. planning to replace floor pans, tank well, and maybe bed floor. Outer body parts are ok with a few whiskey dents with bondo, but not...
Yes, they 12 volted rigged it, and its all thrown in the trash bucket. Gonna be fun hunting a complete 24 volt system for it:D
Uncovered these:
8379
Frame
8380
Engine
I've tried looking thru the data on various sites for clues to identify the year model etc, but no dice.
Unsure what windshield was stuck on it, but I dont think its original.....what yall think?
8378
Getting engine block, crank and head ready for machine shop
8377
More progress, frame ready for blasting.
8376
Here we go!
The specimen as I found it in the wild. Ugly as hell but it spoke to me.
Engine runs on a couple cylinders, and was able to crawl up on the trailer. But It had...