Search:

Type: Posts; User: Patriot

Search: Search took 0.00 seconds.

  1. Replies
    55
    Views
    5,993

    Make sure you have enough gap in the points.

    Make sure you have enough gap in the points.
  2. Replies
    5
    Views
    911

    Yep. Good oil pressure. Thanks.

    Yep. Good oil pressure. Thanks.
  3. Replies
    5
    Views
    911

    IT'S ALIVE! However:

    The oil leaks from the top of the cannister. What is the correct order of the cap and various felt, rubber, and crush washers?
  4. Replies
    2
    Views
    970

    A total Jeep geek observation.

    The listed displacement of the 4 cylinder engines is 134.2 cubic inches. The firing order is 1-3-4-2.

    Coincidence?
  5. Replies
    8
    Views
    1,134

    Thanks. That answers all my questions about the...

    Thanks. That answers all my questions about the oil filter and lines.
  6. Replies
    8
    Views
    1,134

    Anyone got a pic of an F engine with the oil...

    Anyone got a pic of an F engine with the oil filter line routing?
  7. Replies
    8
    Views
    1,134

    Yep, the outlet near the fuel pump was plugged....

    Yep, the outlet near the fuel pump was plugged. Since the filter and return line are brand new (installed somewhere back up the line), it would make sense that it is plugged.
  8. Replies
    8
    Views
    1,134

    Oil filter lines

    Okay, I see that the oil filter fills with oil and the overflow goes out the side and down to the timing gear cover, but where does the oil line come from? I'm working on another person's project...
  9. Replies
    6
    Views
    1,001

    They were Perfect Circle rings. I don't know what...

    They were Perfect Circle rings. I don't know what material they are made of.
  10. Replies
    6
    Views
    1,001

    Well, I received the 0.030 over rings today and...

    Well, I received the 0.030 over rings today and the manufacturer recommended a MINIMUM (yes, they used all caps) of 0.004" per inch of piston diameter. When I received the rings, they would touch...
  11. Replies
    5
    Views
    1,129

    I am almost certain that is was originally a 24 V...

    I am almost certain that is was originally a 24 V system because the battery compartment has room for two batteries but one tray is gone.
  12. Replies
    5
    Views
    1,129

    Thanks. I will count the teeth on the flywheel. ...

    Thanks. I will count the teeth on the flywheel. I'm pretty sure that the Jeep has been converted to a 12 v system because the headlights have 12V on them.
  13. Replies
    5
    Views
    1,129

    Starter questions

    So I tore down the engine for a rebuild and remove the starter. I never heard the starter crank so I decided that it would be a good idea to make sure the solenoid and starter were good.
    ...
  14. Replies
    10
    Views
    1,541

    I ordered a Felpro gasket set from OReillys and a...

    I ordered a Felpro gasket set from OReillys and a set of Perfect Circle rings from ebay. I'm confident both will be good.
  15. Replies
    10
    Views
    1,541

    Nothing wrong with JC Whitney if you fit the...

    Nothing wrong with JC Whitney if you fit the parts. Whoever put the rings in didn't bother to test fit them. I doubt the engine has run in a long, long time. The bearings are great and look new and...
  16. Replies
    10
    Views
    1,541

    The end gap on the rings was greater than I...

    The end gap on the rings was greater than I thought. The rings that came out had an end gap of 0.11" and the oil rings would fall out of the cylinder. It all adds up to zero or very little...
  17. Replies
    6
    Views
    1,001

    The end gap on the rings was greater than I...

    The end gap on the rings was greater than I thought. The rings that came out had an end gap of 0.11" and the oil rings would fall out of the cylinder. It all adds up to zero or very little...
  18. Thread: Engine removal

    by Patriot
    Replies
    3
    Views
    1,440

    Get them from a parts store. They are literally...

    Get them from a parts store. They are literally only a piece of steel with a hole for the head bolt and a hole for the hoist. But most people use a short length of chain with the bolt directly...
  19. Replies
    6
    Views
    1,001

    Thanks. There really isn't a ridge around the...

    Thanks. There really isn't a ridge around the cylinder. It's more carbon build up than ridge. I'm going with a set of 0.020 oversize rings and see if the have a decent end gap.
  20. Replies
    5
    Views
    820

    Wet sand it with 400 grit wet or dry.

    Wet sand it with 400 grit wet or dry.
  21. Replies
    6
    Views
    1,001

    Oversized pistons and ring end gap

    I am in the process of tearing down a F series engine and have a few questions.

    First according to the specs, the bore is 3.125" and when I measure the bore it is indeed 3.125" and there is...
  22. Replies
    10
    Views
    1,541

    See the attached links for the Carter YF and...

    See the attached links for the Carter YF and early Willys Jeep.

    https://drive.google.com/file/d/1Hnga25IxqTWGVJ5Vs9U-ryL4ODXxnrXh/view?usp=sharing
    ...
  23. Replies
    5
    Views
    1,881

    Sticky: Carter YF carburetor info

    I would like to share the info for the Carter YF carburetor with everyone. The info is from 1959 a Motors Manual that was bought new by my father-in-law, The link below should allow anyone to...
  24. Replies
    10
    Views
    1,541

    Not a very friendly bunch here. :(

    Not a very friendly bunch here. :(
  25. Replies
    10
    Views
    1,541

    Hello from Tennessee 1953 M38A1 owner

    Hello. Just bought a 1953 M38A1 Willys Jeep. The previous owner had stripped it down to the bare frame and cleaned and repainted the chassis and suspension and drive train. The fenders will need to...
Results 1 to 25 of 25