Search:

Type: Posts; User: bmorgil

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. I can't wait to hear what that might be. It does...

    I can't wait to hear what that might be. It does look like some type of pre-heat device.
  2. Thread: 1963 Willy’s

    by bmorgil
    Replies
    5
    Views
    66

    Welcome and thank you for your service! It is...

    Welcome and thank you for your service! It is starting to snow here in Northern Ohio. I understand "down for the winter". My son and his friends are just getting their Jeeps out, I am stashing mine...
  3. Replies
    2,009
    Views
    278,105

    Correct, it will only go back in one way. ...

    Correct, it will only go back in one way.

    Thank you for your continued service to our Freedom and Country Ira!
  4. Replies
    6
    Views
    218

    Again it all depends on application. In the case...

    Again it all depends on application. In the case of some of the rear axle bearings on the Timken and the Dana used in the Williys, they are shimmed in and out for proper end play. It is essential...
  5. Replies
    6
    Views
    218

    No problem!

    No problem!
  6. Replies
    6
    Views
    218

    Some bearing cup rotation is allowed. The Cups...

    Some bearing cup rotation is allowed. The Cups need to be able to move in and out for adjustment. Clean the axle bores and the cups should be a very nice slide in fit. As you shim the axles in and...
  7. Thread: Loose lug nuts

    by bmorgil
    Replies
    6
    Views
    191

    If the lug nuts are OK, It is possible someone...

    If the lug nuts are OK, It is possible someone replaced the studs and didn't get them seated all the way. Are you using a torque wrench? Make sure you actually torque the nuts to spec. There are two...
  8. Replies
    6
    Views
    141

    Grouser, I agree with gmwillys, no big deal. I...

    Grouser, I agree with gmwillys, no big deal. I will say however, the best way would be to pull the front and rear driveshaft.
  9. Thread: Loose lug nuts

    by bmorgil
    Replies
    6
    Views
    191

    Are the rims the stock steel?

    Are the rims the stock steel?
  10. Replies
    2,009
    Views
    278,105

    Just think of how much you know about those...

    Just think of how much you know about those brakes being able to slow you down quickly from 60. That will keep you honest!
  11. Replies
    71
    Views
    2,580

    You need a Fabrication guy.

    You need a Fabrication guy.
  12. Replies
    2,009
    Views
    278,105

    Use a Fel-Pro on the valve cover. VS 6617 C

    Use a Fel-Pro on the valve cover. VS 6617 C
  13. Replies
    4
    Views
    331

    Nice 3A! More pictures!

    Nice 3A! More pictures!
  14. Replies
    11
    Views
    576

    I assume you are referencing the whopping 45 HP...

    I assume you are referencing the whopping 45 HP of the VW. If you are taking it to Moab, Yup about 50 all the way is comfy. Though the little air cooled 4 was not very strong the gearing lets it self...
  15. Replies
    12
    Views
    709

    Thanks! Perfect pictures. The drive line you have...

    Thanks! Perfect pictures. The drive line you have would help out a lot of the people who have the old style Detroit. I can now clearly see how it is set up.
    Thanks for the shots!
  16. Mark, there are stainless lines available....

    Mark, there are stainless lines available. https://www.inlinetube.com/products/sjpb6001

    There is a custom stainless bender up in the Detroit area. I can look for his info if you want it. It's...
  17. Replies
    6
    Views
    484

    Man somebody got a nice one!

    Man somebody got a nice one!
  18. Replies
    11
    Views
    576

    HaHa! The first thing I saw was the nice restore...

    HaHa! The first thing I saw was the nice restore project on that truck. 1957 stands as my favorite year for all vehicles. Then I saw the VW! OMG that brings back some serious memories. I had a 1957...
  19. Replies
    2,009
    Views
    278,105

    It sure could be. I Think Ira has the original...

    It sure could be. I Think Ira has the original fuel line setup. It routes the line fairly well. It was running well and then started acting up on him.
  20. Replies
    2,009
    Views
    278,105

    It sure sounds like its going lean. If your sure...

    It sure sounds like its going lean. If your sure the fuel pump is up to spec, I wonder if it picked up some dirt? It would be odd that the float suddenly went off on you. I thought it was running...
  21. Replies
    2,009
    Views
    278,105

    It sounds like you definitely need that...

    It sounds like you definitely need that equipment. Very cool setup that is for sure!
  22. Replies
    2,009
    Views
    278,105

    I am loving all this history! I think they had...

    I am loving all this history! I think they had one of those "platform" vehicles at the Toledo Jeep Fest inside near LarrBeard's truck. It had what looked like a small engine mounted under a platform....
  23. Replies
    2,009
    Views
    278,105

    Definitely could cause it. "Up and down" sure...

    Definitely could cause it. "Up and down" sure sounds like lean then back and lean and back. A leak on the suction side could cause more than a bubble. The pump could keep loosing prime. I agree with...
  24. Replies
    6
    Views
    484

    That is definitely "pretty on the outside". The...

    That is definitely "pretty on the outside". The mechanical aspect will be well worth it on a perfect body like that. A ton of the restore process is in the body etc. Everything that looks great on...
  25. Replies
    4
    Views
    434

    Wow some real good stuff there! I want a Willys...

    Wow some real good stuff there! I want a Willys truck now! After sitting in LarrBeard's, I can tell you those are some real nostalgic vehicles.
Results 1 to 25 of 480
Page 1 of 20 1 2 3 4