Search:

Type: Posts; User: bmorgil

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 49 minute(s) ago.

  1. Replies
    6
    Views
    97

    Jeff I have used both ways. A nylon wedge or the...

    Jeff I have used both ways. A nylon wedge or the brakes if they are there. The brakes will apply a sufficient load easily. Typically I have used a Nylon wedge. I will say if you can use them, the...
  2. Replies
    6
    Views
    97

    1. Are shims typically standard thicknesses like...

    1. Are shims typically standard thicknesses like 3 thou, 7 thou, 10 thou, 15 thou etc. ? Yes typicly you get them in .005 increments. They are available in .001 increments however, if you are able to...
  3. Thread: 1953 cj3b

    by bmorgil
    Replies
    7
    Views
    146

    Nice Jeep joey! Love the blue. Great resto there...

    Nice Jeep joey! Love the blue. Great resto there for sure.
  4. Replies
    10
    Views
    246

    Nice picture Larry! I think you can get arrested...

    Nice picture Larry! I think you can get arrested for that.
  5. Replies
    10
    Views
    246

    Guessing is the only thing you can do until you...

    Guessing is the only thing you can do until you compare it to a good reading. They all seem to have a mind of their own. Odds are its around 160. The chepo point and read infared thermometers from...
  6. Replies
    7
    Views
    290

    I am thinking TJ is on to it. It sounds like the...

    I am thinking TJ is on to it. It sounds like the clutch might be gone.
  7. Replies
    14
    Views
    490

    I have this set and it will drill frame rails. It...

    I have this set and it will drill frame rails. It is a shallow drill however, and costly.
    ...
  8. Replies
    7
    Views
    290

    Moose, more pictures of that nice little red jeep!

    Moose, more pictures of that nice little red jeep!
  9. Just a dust cover Mark. It is not shown on the...

    Just a dust cover Mark. It is not shown on the illustrations. I am guessing it was added later. Probably a service fix for crap getting in there.

    I never get to use my horn because by the time I...
  10. Cindy knows I care.

    Cindy knows I care.
  11. Thread: Idling High

    by bmorgil
    Replies
    3
    Views
    189

    I am not sure what carb you have but there are...

    I am not sure what carb you have but there are two adjustments to make. The idle speed and the idle mixture. The idle speed adjustment will be on the throttle plate (the piece the throttle linkage...
  12. Replies
    15
    Views
    631

    "Hot Hammer" and "Gas Axe" I am definitely filing...

    "Hot Hammer" and "Gas Axe" I am definitely filing those in the keeper box! Hilarious.
  13. Either will work. There are two in there because...

    Either will work. There are two in there because two different ones were used depending on the serial number. It doesn't matter which one you use as long as you used one.
  14. Replies
    13
    Views
    549

    Sweet, just plain SWEET!

    Sweet, just plain SWEET!
  15. Replies
    14
    Views
    490

    Where did you get the hole saw? I have had a...

    Where did you get the hole saw? I have had a tough time finding hole saws that reliably cut metal. I have a carbide set but it doesn't have much depth capability, and they cost a bit.
  16. Thread: Idling High

    by bmorgil
    Replies
    3
    Views
    189

    D66, you may want to look for a vacuum leak. They...

    D66, you may want to look for a vacuum leak. They can be hard to find, but spray some carb cleaner around the intake surfaces and carb base. Listen for changes in the idle. Look for any cracked...
  17. Replies
    6
    Views
    268

    Nice start man! That is going to be a nice...

    Nice start man! That is going to be a nice restoration.
  18. Replies
    14
    Views
    490

    For sure new studs. This is a time to take the...

    For sure new studs. This is a time to take the opportunity to make them all right hand thread if you desire. I changed mine over to all right hand. Some people do and some don't.
  19. Replies
    961
    Views
    201,749

    Counting the days, praying for good weather!

    Counting the days, praying for good weather!
  20. Replies
    14
    Views
    490

    I agree with gm. A Dremel and a lot of time or...

    I agree with gm. A Dremel and a lot of time or buy one of these. https://goodson.com/collections/arbors-accessories/products/swedge-tools%20

    I used a press and a LOT of force. The drum and stud...
  21. Replies
    17
    Views
    1,649

    If you are going to "use it", I don't think you...

    If you are going to "use it", I don't think you can go wrong with good front disc's and good rear brakes, with a dual master cylinder. For the show and parade original is nice. Using it on and off...
  22. Thread: New Guy Here

    by bmorgil
    Replies
    6
    Views
    253

    Welcome aboard! Here you go DW. ...

    Welcome aboard!

    Here you go DW.

    https://willysjeepforum.kaiserwillys.com/showthread.php?2451-How-to-post-a-picture-in-a-thread
  23. Replies
    15
    Views
    631

    Beware the Tornado! I will try to make you feel...

    Beware the Tornado! I will try to make you feel better and say, I have definitely seen much worse than that. Mine was pretty bad. About all of the internals had to be replaced. Even my transmission...
  24. Replies
    15
    Views
    631

    It sounds like you might have had some water in...

    It sounds like you might have had some water in there Jeff. Wow that thing was stuck. I have a brass drift just slightly smaller than the shaft. You can hit it pretty good without damage. I have...
  25. Thread: 47 cj2a

    by bmorgil
    Replies
    5
    Views
    209

    The outer tube is clamped on at the bottom to the...

    The outer tube is clamped on at the bottom to the box. There is a clamp and bolt assembly.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4