Hi guys I'm back and needing a little help on this turn signal issue.
Problem I am having is I can't get the turn signals to flash. I followed the wiring on the new signal unit but no matter if I...
Type: Posts; User: Btroy
Hi guys I'm back and needing a little help on this turn signal issue.
Problem I am having is I can't get the turn signals to flash. I followed the wiring on the new signal unit but no matter if I...
Nice send me a PM with what you are asking for them.
Thanks for the info and pics. I sure don't want to install round gauges unless absolutly needed.
I see you live in Ft Wayne, I grew up in Anderson.
Now thats funny ....I did that already as I put that last diagram up somewhere and now I can't find it. I hear Ya! :)
3594
3595
Thanks again.
Hi guys, I am wanting to retain the origanal gauges in my 53 Willys truck, I have looked the inter-web high and low and have not seen where I might get replacement gauges of this type. If there is...
Nice truck, looks like mine. Same color and all. I have the 4 cylinder and converted to 12v, this was because it set outside with the hood open for who knows how long before I bought it.
When you...
Update as I hate to leave threads unanswered.
Success finally..:)
I was able to get my 53 running after a complete refresh and conversion.
I followed the wiring diagram but not sure if I...
Thanks for the diagrams, I am pretty sure its wired correctly as I followed the new wiring diagram I got with the hasness, I will verify once again.
Thanks for your time really appreciate this.
Can someone tell me the minimum wires I need to start the engine?
Wondering if the plug wires are correct as I whitched to 12 volt system.
Currently I only have the negative side of the coil...
Mines a 53 but here are some pics. Top pivots from bottom up, bottom pivots from front up. So to access below seat you lift back then lift bottom. Back will rest on bottom to keep it up.
At least...
That has changed, I went ahead and bought a distributor from our host with the electronics
In it.
It appears I maybe burning up
The coils. Now when I test the secondary
It is showing 9.9 on...
Ok new coil and I get spark with it as in drawing.
But when I connect up the wires
It cranks but no fire from the coil tower now?
Ok looks like the new coil is bad, as from + to - it measures 03.4. From center to - my meter does not move.
I will get another coil.
Thanks for your assistance. Will reply once I get another...
I went ahead and bought a new electronic distributor from our host. I am still not getting any spark.
I have a flame thrower coil. The instructions say it has to be an internal resistor type or I...
Cap was removed and rotor is turning CCW as expected.
Also measured voltage on negitive side of coil while cranking and it is thwe same as the postive side 9-8 volts.
Hi guys I'm back on my 53 Willys truck project.
Got the motor back together and have fuel but no spark. I converted to a pertronix but can't figure out why I'm not getting any spark.
With the...
Still working on this but have an issue when cranking, if I go from ground to the positive side of coil I see 12v while cranking. If I measure between the pos and negative post on the coil I get 0...
There is a problem with that, there is noway to keep the vacuum advanced installed as there is no provision to connet the vacuum pod to the points plate that was removed. I will try it without and...
Hi guys, back again. I attempted to fire up my 53 after I renewed it. Points were replaced but the wires burnt. I want to convert to pertronix but my dist has a vacuum advance. Do I eliminate that as...
Ok thanks for the explanation. It was my understanding it used to be a forestry service truck then went to a fire department. Could have been added at that point. Appreciate your input.
Working on my 53 truck and I have a dash panel directly in front of the steering wheel. Can I get some help identifying what this
Ok thanks for the info.
Hi guys, I'm making progress on my 53 truck, have the engine rebuilt converting to 12v. I bought a 12v regulator along with my new wiring hardness. Will have to splice the battery wire so it will...
2158
One side.
I have received that catalog, it's great.
Thanks
2159
Picture of outside