It looks like you may have the wrong thread pitch on the hose end causing you the problem, since your old hose was properly seated. I know that there have been some issues in the past with the hoses...
Type: Posts; User: gmwillys
It looks like you may have the wrong thread pitch on the hose end causing you the problem, since your old hose was properly seated. I know that there have been some issues in the past with the hoses...
I don't remember if the Dana 44 has the vent on the differential cover or on the top of the axle tube. If yours does not have a vent in the cover, then there should be a vent hose attached to the...
It sounds like to me that you have two issues going on. If your pedal travel is drifting to the left during the travel, then I would first check the brake/clutch cross shaft bushings to ensure that...
The primer looks good. Again, for a first timer, you are doing a great job! Axle nuts are one of those items that need to be checked from time to time. Whenever I have a wheel off the ground...
It's odd to me that with all the technology that's out there, the radios that we install today are Vietnam era technology with some updated receivers, (probably 90s). There are some digital...
Most of the throw out bearings are now sealed, but before there was a grease zerk that needed a shot of grease from time to time. Now that they are sealed, you install and forget now. Sometimes...
The 10 plies will definitely ride rougher than a radial. You can run a lot lower air pressure on the bias plies (15 to 25psi) to soften the jounces. For mainly forest service minimum Maintenace...
Fantastic. The speaker sounds pretty good, and will make for a good effect.
It would be a wise investment to replace the worn items. When in doubt, change it out. Money spent now may save you a lot later on, especially if your brakes or clutch do not respond while driving...
The Power King has been around for a long time and have been a staple store brand tire at many farm supply stores, and they are tough as nails. A question you may want to ask yourself is how are you...
There are three bolts on the pressure plate that adjust the fingers of the pressure plate, but you should not have to adjust those. The best way is to adjust the cable linkage to where you have 1/2"...
That will work!
Ma deuces are probably the coolest round slingers around. We used to have to do remote weapons testing, so we would go over to the armory to sign out a deuce to put on the cradle...
12 volts make life a lot less troublesome. Most of the reason for folks to convert from 24 to 12 is mainly the costs involved with replacement parts.
Two possibilities for a run away pedal:
1) if the brake pedal moves side to side or rotates, you can fix that the low buck way. If the tightening the bolt for the pedal doesn't solve the issue,...
A quick Mrs. Google search came up with an hour's worth of combat radio chatter. With further digging, I'm sure you could come up with artillery specific chatter, since there are files for air...
Some radio units when presented at rallies/shows have recordings of fire missions, (air strikes or artillery) playing over the speakers in a loop. It adds an extra level of presentation to your...
The CJ5s had a rubber pad on the clutch and brake;
https://www.kaiserwillys.com/products/clutch-brake-pedal-rubber-pad-fits-55-67-cj-5/
The following diagram shows all the bushings for the...
A couple of questions in regard to how your M38A1 is configured? Is the electrical system still 24 volt? Are you running the waterproof plugs and wires? The waterproof wires require an adapter to...
I'm liking your rear bumper. Looks great!
The battery boxes look better than new! Well done!
Like Bmorgil and 56willys have said, the dimensions for the battery tray can be closely matched to the CCAs you would like to run. As you said, you don't need a whole lot for your region you...
Hodakaguy,
Outstanding M38, and an awesome road trip to boot! Being that your rig received a first place award from the MVPA, (think Bloomington Gold for Corvettes) that says a lot about the...
You can do either that Bmorgil said. In my opinion, since you already have the new mount handy, clean the frame really well and start at one end welding the new bracket in. As you hear up the...
Yep, you all helped to talk me out of it.... Like I need more projects to keep up with and taking time from finishing others.
It's not a good idea to not run a thermostat at all. The water needs a resistor to slow it down when going through the radiator to get the heat transfer out of the water. If you do choose to remove...