Search:

Type: Posts; User: gmwillys

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    112
    Views
    7,643

    Check eBay for a Jeepers Creepers. You should be...

    Check eBay for a Jeepers Creepers. You should be able to find some vintage pieces that would complement Cindy.
  2. Replies
    2,274
    Views
    320,529

    It may be a good idea to start a new thread for...

    It may be a good idea to start a new thread for those who are looking at reading up on an engine build as a main subject.

    Magoo has come a long ways, and the finish line is in sight.
  3. Replies
    423
    Views
    48,172

    Sweet! Between Summit, Jegs, and Speedway...

    Sweet! Between Summit, Jegs, and Speedway Motors, if they don't have what you need you don't need it.
  4. Replies
    2
    Views
    63

    Welcome Daniel, The Studebaker engine swap was...

    Welcome Daniel,

    The Studebaker engine swap was a '50s - '60s power adding swap. The truck appears to be in restorable shape from the photo, and would be worth something to someone. The real...
  5. Replies
    2,274
    Views
    320,529

    The trailer is in fact for an M151. The dead...

    The trailer is in fact for an M151. The dead giveaway is the wheels and the angled off fenders.
  6. Replies
    2,274
    Views
    320,529

    The plugs are pipe thread, so they need some pipe...

    The plugs are pipe thread, so they need some pipe dope to prevent oil from migrating through the threads to your clean driveway or shop floor. If your cover gasket leaks, then your cover is not...
  7. Replies
    5
    Views
    133

    Welcome Willys@57, The original configuration...

    Welcome Willys@57,
    The original configuration would have the filter assembly mounted on the engine. It is difficult to say what filter you may have without seeing pictures of your ride. Most...
  8. Replies
    9
    Views
    328

    The last rotten frame I had turned out fairly...

    The last rotten frame I had turned out fairly descent. I'm sure yours isn't too bad.
  9. Replies
    9
    Views
    328

    To add pictures go to Go Advanced tab on the...

    To add pictures go to Go Advanced tab on the bottom right of the Quick Reply window. The top of the Advanced window has several options to add pictures. I use the paper clip to add pictures from my...
  10. Replies
    8
    Views
    217

    All is good. The stud is wet by design, so add...

    All is good. The stud is wet by design, so add some pipe dope or Loctite thread sealant to the new stud and you'll be good to go.
  11. Replies
    423
    Views
    48,172

    Looks too good to cover it with a body.

    Looks too good to cover it with a body.
  12. Replies
    112
    Views
    7,643

    You'll be able to stop on a dime with change to...

    You'll be able to stop on a dime with change to spare.
  13. Welcome Sabine! Nice looking CJ-6! LarrBeard...

    Welcome Sabine! Nice looking CJ-6! LarrBeard has all the answers.
  14. Replies
    5
    Views
    246

    We had new glass installed in our 2A reproduction...

    We had new glass installed in our 2A reproduction windshield frame. I purchased the seals to go around the windshield panes but ended up not fitting correctly. The repro frame was slightly thinner...
  15. Replies
    2,274
    Views
    320,529

    That was money well spent! Good machine shops...

    That was money well spent! Good machine shops are hard to come by these days, or at least they are getting fewer and farther between.
  16. Replies
    9
    Views
    328

    Welcome Spence. Please post some of your two...

    Welcome Spence.

    Please post some of your two wheel rides! I live not too far from the Barber Motorsports Park in Leeds AL. They have a museum there that is jam packed with vintage bikes. I love...
  17. Replies
    2,274
    Views
    320,529

    Just like an old Harley. If it stops leaking,...

    Just like an old Harley. If it stops leaking, it's low on oil.
  18. Replies
    11
    Views
    555

    Looks great! A little history lesson from a...

    Looks great!

    A little history lesson from a brain full of semi worthless knowledge. The NDT (non directional tread) was a military staple from WWII until the early '80s with the introduction of...
  19. Replies
    2,274
    Views
    320,529

    Good deal! Drips are just part of the experience...

    Good deal! Drips are just part of the experience of having a darn near 70 year old hunk of Iron and steel. Our '46 2A leaks from the rear main, and eventually it will get fixed, but for now there...
  20. Replies
    2,274
    Views
    320,529

    The crown of the road, and the nature of non...

    The crown of the road, and the nature of non directional bias plies, that will most likely be as good as it gets.

    That is the reason I don't want to paint the 2A. Nothing says go away like rusty,...
  21. Replies
    2,274
    Views
    320,529

    To prevent scarring of the tie rods with a pipe...

    To prevent scarring of the tie rods with a pipe wrench, on a straight axle suspension I would put it up on stands. With all new tie rod ends, it should adjust by hand with the weight off of the...
  22. Replies
    1
    Views
    222

    Welcome! It may be my crappy eyes but I can't...

    Welcome!
    It may be my crappy eyes but I can't make out the prefix on the serial number. From what I can tell it appears to be a CJ from the civilian dash plate at the bottom of the second photo....
  23. Replies
    11
    Views
    679

    That's better. I was beginning to worry.

    That's better. I was beginning to worry.
  24. Thread: 1957 cj-5

    by gmwillys
    Replies
    54
    Views
    3,356

    Once upon a time, the farm stores, ( Farm & Fleet...

    Once upon a time, the farm stores, ( Farm & Fleet in the Midwest, and the true man-mall Fleet Farms in the upper Midwest) you could dig through and find hoses on your own. Down in the south land,...
  25. Thread: 1957 cj-5

    by gmwillys
    Replies
    54
    Views
    3,356

    On odd ball projects, I like to take measurements...

    On odd ball projects, I like to take measurements of both the necks on the engine, and the rad necks. Then bend brazing rod to the shape desired for the routing. Then pay the local Napa store to...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4