Search:

Type: Posts; User: bmorgil

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    132

    After 4 pumps 75# cold is not surprising on a...

    After 4 pumps 75# cold is not surprising on a cold or cool motor. 65# is low and that 55# number might just miss once and a while. If you had it warm, a little closer to at least 90# min would have...
  2. Replies
    8
    Views
    175

    It is forever preserved in the Tech Library. ...

    It is forever preserved in the Tech Library.

    https://willysjeepforum.kaiserwillys.com/showthread.php?1820-Start-up-Best-Practices
  3. Thread: 1945 mb

    by bmorgil
    Replies
    2
    Views
    67

    Lone Rider, love that name, it sounds like you...

    Lone Rider, love that name, it sounds like you have a very nice representation of the last of the MB's. I would say someone did something to the motor. The casting number is correct for the early...
  4. Replies
    118
    Views
    16,797

    You are getting busy now! Don't ya love it when...

    You are getting busy now! Don't ya love it when the parts come in.
  5. Replies
    34
    Views
    1,295

    A loaded question there. The effort to turn the...

    A loaded question there. The effort to turn the wheel is going to be more of a factor of the weight of the vehicle.These things are fairly light. They are manual steering and it takes a bit of effort...
  6. Replies
    8
    Views
    175

    You really have something there Steve! The best...

    You really have something there Steve! The best vehicles to restore come from the "Sun Belt" here in the USA. A California car is what everyone is looking for. The sun states are the best for old...
  7. Replies
    5
    Views
    135

    Yes the original military engines used the rope...

    Yes the original military engines used the rope seal for sometime. The service manual only refers to the change as "on early L134 engines a wick type seal was used", "on later L134 engines a steel...
  8. Replies
    5
    Views
    135

    Be sure you measure the crankshaft surface. If...

    Be sure you measure the crankshaft surface. If the crankshaft diameter at the seal is not correct, no rubber seal will work. I did read a while ago about "cheap" rear main seals having a wide lip and...
  9. Replies
    5
    Views
    132

    jw, if you are confident in the condition of the...

    jw, if you are confident in the condition of the cap, rotor, points, coil, plugs and wires the next step is compression. Assuming the carburetor is ruled out as a problem, warm it up first and follow...
  10. Thread: Horn Rebuild

    by bmorgil
    Replies
    2
    Views
    87

    I am not sure how the wire runs on those VT. On...

    I am not sure how the wire runs on those VT. On the CJ's with the Ross box, the wire runs all the way through the middle of the box and comes out the bottom.

    Well I hope you heal up fast VT, these...
  11. Replies
    8
    Views
    340

    You always must have a project for another day!

    You always must have a project for another day!
  12. Replies
    2
    Views
    67

    Welcome Jeff, its in great shape! Those look like...

    Welcome Jeff, its in great shape! Those look like the original Warn hub locks on there. lets see more pictures of it.
  13. Replies
    5
    Views
    135

    Definitely something wrong. This is from a prior...

    Definitely something wrong. This is from a prior post I wrote. They were having similar trouble with the rope seal.

    "With a rope seal the crankshaft (no rods or pistons hooked up) should turn...
  14. Replies
    430
    Views
    58,676

    It certainly looked and sounded like a good idea....

    It certainly looked and sounded like a good idea. Bed liner is tough and goes on thick. I kinda wonder what went wrong?
  15. Replies
    7
    Views
    238

    Nice party Larry! That brown CJ is set up to go a...

    Nice party Larry! That brown CJ is set up to go a lot of places.
  16. Replies
    430
    Views
    58,676

    This stuff works very well. ...

    This stuff works very well.

    https://plastidip.com/our-products/plasti-dip/ I have used it on everything from eye glass stems around the ears, to tool handles.

    I use their liquid tape in marine...
  17. Replies
    8
    Views
    175

    Nice find! Questions are the most fun, and an...

    Nice find! Questions are the most fun, and an important part of the restore. Everyone on this forum will help if they can.
  18. Replies
    1,059
    Views
    583,645

    Nice job young man! Gotta love that.

    Nice job young man! Gotta love that.
  19. Replies
    430
    Views
    58,676

    That is an ominous warning jb! I can't wait to...

    That is an ominous warning jb! I can't wait to watch the next episode.
  20. Replies
    7
    Views
    238

    Nice!! I would like a bottle of that. A great...

    Nice!! I would like a bottle of that. A great year indeed!
  21. Replies
    12
    Views
    1,057

    There are a few gear vendors out there. The extra...

    There are a few gear vendors out there. The extra at KW goes into the no questions asked returns. You really don't have to worry about what you buy from them. No matter what, they will take it back....
  22. Replies
    12
    Views
    1,057

    gm has you on the right track. Any surface that...

    gm has you on the right track. Any surface that bearings will be running on, will not tolerate pitted surfaces for long. Your bearing surfaces need to look good with no damage. Under the bushings you...
  23. Replies
    11
    Views
    483

    Wow some great info on it already. That is a...

    Wow some great info on it already. That is a perfect find 43,000 miles, that's fantastic. It definitely looks like a buff and a shine and its ready to go! What a great start.
  24. Replies
    11
    Views
    483

    That thing looks like it is in great shape!

    That thing looks like it is in great shape!
  25. Replies
    430
    Views
    58,676

    There looks like there might be a few there! Now...

    There looks like there might be a few there! Now that's a place I would like to visit. Nice find Larry!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4