Search:

Type: Posts; User: gmwillys

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds; generated 21 minute(s) ago.

  1. Not an uncommon issue. A new set of Stainless...

    Not an uncommon issue. A new set of Stainless valves will cure that. A piece of advice though, I would look to have hardened seats installed. This isn't mandatory, but if you do, you will not need...
  2. Replies
    965
    Views
    202,730

    Much like a Harley and old dogs, constantly...

    Much like a Harley and old dogs, constantly marking their territory.

    I would look at the output yoke sealing surface first. The brake would have to be way too tight to cause enough heat to mar up...
  3. Replies
    26
    Views
    2,289

    That's why the cowl vent is so nice to have. Pop...

    That's why the cowl vent is so nice to have. Pop it up, and your toes will be a little less broiled at speed.
  4. Replies
    26
    Views
    2,289

    Tops are over rated, at least for us CJ guys.

    Tops are over rated, at least for us CJ guys.
  5. Welcome Emmett, First things first, your fuel...

    Welcome Emmett,

    First things first, your fuel pump is in need of a rebuilding / replacement. The fuel pump is leaking internally, allowing fuel to leak into the crank case. Just be careful when...
  6. Thread: 1953 cj3b

    by gmwillys
    Replies
    7
    Views
    197

    Both the 3B and the '66 Swept line are great! ...

    Both the 3B and the '66 Swept line are great! Thank you for posting the videos!
  7. Replies
    35
    Views
    2,143

    Great! In my opinion, keep the second Jeepster...

    Great! In my opinion, keep the second Jeepster for an every day driver when weather isn't quite favorable for your prestine restoration. Then when offered a good price let it go.
  8. If the compression test comes back within...

    If the compression test comes back within tolerance when warm, then we may need to revisit the firing order. The way I'm reading the steps taken to this point is that the backfire happened after the...
  9. Replies
    965
    Views
    202,730

    How did the ride go? I should have taken the...

    How did the ride go? I should have taken the heep out this weekend, but was doing other things. It won't be long before it will be time to pack wheel bearings on the car hauler and shoot north.
  10. Replies
    1
    Views
    135

    Welcome Peter Latallo, Those are some...

    Welcome Peter Latallo,

    Those are some interesting factory holes. I have not seen that configuration before myself, but I have never had an MB in the inventory. My best guess would be for commo...
  11. Replies
    13
    Views
    561

    Great condition! We look forward to learning...

    Great condition! We look forward to learning more about your new ride!
  12. Replies
    14
    Views
    502

    We have you covered. If you would like to be...

    We have you covered.

    If you would like to be period correct, the driver's side calls out for left handed threads. The links are for the left handed thread studs and lug nuts;
    ...
  13. Replies
    15
    Views
    638

    Gas Axe is my favorite term.

    Gas Axe is my favorite term.
  14. Replies
    14
    Views
    502

    I would look to replace the studs if you are...

    I would look to replace the studs if you are going as far as to removing them. Over time they have stretched from being torqued multiple times.

    With that being said, if you do chose to reuse...
  15. Replies
    6
    Views
    273

    Welcome Mark Schoening, Great looking '51! I...

    Welcome Mark Schoening,

    Great looking '51! I like your plan for a dependable driver. We look forward to watching and helping out your progress. Please feel free to ask any questions that you...
  16. Thread: 47 cj2a

    by gmwillys
    Replies
    5
    Views
    224

    No problem! The new frame steel isn't a bad...

    No problem!

    The new frame steel isn't a bad plan at all. I just so happened to have a spare frame that was rotten in the middle. I like to salvage all that I can from the too far gone Heeps to...
  17. Replies
    14
    Views
    502

    Welcome oldjeepguy! I would use a Dremel tool...

    Welcome oldjeepguy!

    I would use a Dremel tool to clean up the displaced metal around the stud. If the studs have ever been changed in the past, they may not be too pinched in. A press will...
  18. Thread: New Guy Here

    by gmwillys
    Replies
    6
    Views
    260

    Welcome Jeep45! As LarrBeard said, we love...

    Welcome Jeep45!

    As LarrBeard said, we love seeing all of your interests. Tractors, gas pumps, hit and miss engines, and airplanes are all checks in the cool column around here. Please let us...
  19. Thread: 47 cj2a

    by gmwillys
    Replies
    5
    Views
    224

    I understand your plight with the front...

    I understand your plight with the front bumper/frame hack. On our 2A, it had a 4" piece of well casing for a front bumper, and the front frame rails were scabbed over with scrap metal for...
  20. Replies
    3
    Views
    273

    Well done on the broken bolt removal. Your...

    Well done on the broken bolt removal. Your pictures are great as well!
  21. Replies
    965
    Views
    202,730

    Until the next upgrade.

    Until the next upgrade.
  22. Replies
    965
    Views
    202,730

    Good topic! To answer the question, in a round...

    Good topic!

    To answer the question, in a round about way, no. Willys didn't typically paint the embossed lettering until the '50s. That doesn't mean that the dealer didn't spruce up the details...
  23. Replies
    57
    Views
    6,064

    Joey, if you have a plumber's torch, (hand held...

    Joey, if you have a plumber's torch, (hand held propane or Map gas torch) use it to warm up the hub nut enough for it to get hot. Spray some penetrating oil at the threads while hot then repeat the...
  24. Replies
    13
    Views
    561

    CW, Thank you for your service! We look...

    CW,

    Thank you for your service!

    We look forward to seeing your purchase when it becomes available. There is no better time machine than an Willys.
  25. Replies
    13
    Views
    561

    Welcome CW! Since you have experience with...

    Welcome CW!

    Since you have experience with just about every generation of Jeep that has been produced, the question is what would you like for a tool around rig? Depending on your location, the...
Results 1 to 25 of 498
Page 1 of 20 1 2 3 4