"Should be a breeze to adjust them properly ..."
Probably not, but you'll get it done and you'll be a lot wiser when you finish. You'll probably have at least one skinned knuckle invested in it...
Type: Posts; User: LarrBeard
"Should be a breeze to adjust them properly ..."
Probably not, but you'll get it done and you'll be a lot wiser when you finish. You'll probably have at least one skinned knuckle invested in it...
"I generally start shopping the internet after learning something isn’t available locally."
A typical example: I needed some pieces and parts from my local Fastenal. They were not in stock...
We know where to find most parts, but rebuilders have their own preferred sources and many times their preferred sources for small block Chevy parts come up as a blank when we ask them to find a set...
It looks like what a Dana 25 should look like ... NICE!
"6-8 week to turn into 16 months"
And the engine job .. "COVID"
"By the way, does anyone have an opinion on whether the new style seal (with rubber) or the old style seal (leather?) is better?"
Opinions are like armpits around here - every one has a couple and...
"Here is a link to a Spicer failure analysis manual"
There are some gruesome pictures in there. The ones with pictures of water damage and spalling from poor lube are typical of what will be found...
Enjoy the time with the boys. The Jeep can wait - they can't. I'm very lucky - my kids and grandkids are past the coaching stage, but I've ended up as coach for a Junior High Power Shooting Team. ...
Now we know where to go to borrow a steering wheel puller ... :)
It was a good question, honestly asked and answered. Now a whole bunch of us know a little more about Jeeps. That's how we learn.
I've never seen any lube instructions for a carburetor....
Places where a shaft goes through a sleeve or bushing could take a dob of grease - but there is enough gas around the carb that just...
"Take a look at this picture that shows what the bell housing looks like."
When we pulled the truck out of the barn, it smelled like mouse pee. The start of the restoration was to pull out the...
We complain about how all of the little things we find make the project take longer and cost more - what we don't appreciate is how many headaches we avoided later on by fixing things right the first...
Yayyyy ...
"Auburn Clutch Company, Auburn, IN".
About 20 minutes north of Ft. Wayne.
https://willennar.pastperfectonline.com/photo/3E0F4D15-B8F9-438B-90A6-203876836372
Another northeast...
Keep the original thread - it's kind of like home now and we know where to find you.
Kind of like this works ...
You know all of that good stuff - that's why "you da' man"
BMorgil: You suggested:
https://www.melling.com/parts-lookup/.
I'm not in the market for a pump, but what sets these folks apart as a pump supplier? You seem to know where to find the good...
A comment from the peanut gallery:
I'd let him have the distributor so he can set static timing. Getting the distributor drive gear on the right tooth on the camshaft driving gear can sometimes...
"The only bad thing (for me) is the expense, which will run me about $4K."
As a comparison, an F-134 rebuild in NE Indiana six years ago was $3,100, but that did not include balancing - just...
"... there are "sick" guys like you ..."
Yep, that's us - just don't leave out "and twisted" when you describe us.
"Checked compression last night on the engine. 90 psi, 5, 75, and 90 when "dry"."
It will be interesting to see what is in the 5# hole. That looks like something broken (valve, piston), not just...
A. Everyone lost stuff from 28 August until about yesterday.
B. I'll have to do a search to see if there is anyone local that specializes in Jeep engine rebuilds.
The good news is that Jeep...
"If a wheel cylinder or line is leaking, crimp off that section,.."
I'd suggest that GMwilllys means crimp off either the front or rear brakes, not just the right front or left rear....
Or for...
"Inject a few ounces of fuel into the carburetor bowl down the vent tube, prime the carb and see if it will run and fill the bowl from the pump. If it runs for a few minutes and runs out of fuel, the...
"I'm starting to believe the carburetor is the issue and would like some input on what my next steps might be. Is it possible the float is stuck or the jets are clogged and I need to take the carb...