Search:

Type: Posts; User: bmorgil

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    6
    Views
    133

    VT just make sure you have free play at the...

    VT just make sure you have free play at the pedal. About 1" at the pedal is plenty. Free play is the distance between the throw out bearing and the fingers on the clutch pressure plate. You want the...
  2. Replies
    47
    Views
    15,774

    An X sized socket will work. You can make your...

    An X sized socket will work. You can make your own tool with 2 sockets and/or washers and a piece of all-thread and two nuts. You need to be sure the seals push in square.
  3. Replies
    113
    Views
    65,092

    Hopefully the lesson was well learned! The flying...

    Hopefully the lesson was well learned! The flying isn't bad, the landing is usually rough.
  4. Replies
    113
    Views
    65,092

    Yikes! That mailbox jumped right out there.

    Yikes! That mailbox jumped right out there.
  5. Thread: Running to hot

    by bmorgil
    Replies
    5
    Views
    87

    I used a Champion in mine. I had to do a little...

    I used a Champion in mine. I had to do a little work to make it fit but, it went pretty well. The other option is to purchase a reproduction. The reproduction can get expensive.
    ...
  6. Thread: New to Forum

    by bmorgil
    Replies
    3
    Views
    55

    Welcome JB! Lets see the beasts.

    Welcome JB! Lets see the beasts.
  7. Replies
    1,036
    Views
    483,136

    I cant wait to watch this one grow!

    I cant wait to watch this one grow!
  8. Thread: Steering

    by bmorgil
    Replies
    1
    Views
    47

    Not really. You might be able to take out a very...

    Not really. You might be able to take out a very small amount but you will run into the stops on the sector shaft on full turns. The high point is adjusted at assembly and isn't really a wear...
  9. Thread: Running to hot

    by bmorgil
    Replies
    5
    Views
    87

    Steve what do the plugs look like? Is it steaming...

    Steve what do the plugs look like? Is it steaming them? Is there white steam in the exhaust? If the head gasket is blown there should be bubbles in the water in the radiator when the engine is...
  10. Replies
    3
    Views
    58

    That's a nice looking Jeep! It is certainly all...

    That's a nice looking Jeep! It is certainly all there. I will tell you nothing will come in more handy than the service manual when it comes to working on your brakes.
  11. Replies
    267
    Views
    27,594

    I was thinking some 24's so you could strap on...

    I was thinking some 24's so you could strap on some Mickey Thompson Baja Pro XS 21/58-24LT's! The 58" diameter should give you adequate ground clearance.
    ...
  12. Sorry about that Wulfie, I should have clarified...

    Sorry about that Wulfie, I should have clarified that! All of the weight sits on the top rubber on top of the cross member. Here is a photo from underneath (its blurry I couldn't hold still standing...
  13. Replies
    6
    Views
    133

    I can see it is getting quite a notch worn into...

    I can see it is getting quite a notch worn into it at the one end. I would say time to replace that one
  14. Mike, The Willys F4-134 was introduced in 1950....

    Mike, The Willys F4-134 was introduced in 1950. It was in civilian Jeeps, CJ-3B, CJ-5, and CJ-6 models. It was also used in the Willys 473 and 475 pickups, wagons, and sedan deliveries. If you have a...
  15. Here is a pic of how it goes. Everything sets on...

    Here is a pic of how it goes. Everything sets on the cross member and the bolt goes through the cross member.

    9388
  16. Replies
    160
    Views
    41,995

    Looking good Joey!

    Looking good Joey!
  17. Replies
    20
    Views
    829

    The exact tray might be tough to find, but I used...

    The exact tray might be tough to find, but I used one of these.

    https://www.kaiserwillys.com/nsearch/?q=battery%20tray
  18. Replies
    32
    Views
    1,604

    I would just use the block. Rebuild it as if it...

    I would just use the block. Rebuild it as if it was a Willys 134. Have the shop use the WIllys parts and the new block. It is possible there are different components in the engine. If the valves are...
  19. Replies
    267
    Views
    27,594

    Definitely the part that separates the men from...

    Definitely the part that separates the men from the boys. The turbo plumbing is artwork.
  20. Replies
    6
    Views
    133

    VT I would start by trying to adjust the clutch...

    VT I would start by trying to adjust the clutch free play. They don't need much. Just a half inch at the pedal should be a good place to start. If you cant get the free play correct, the linkage...
  21. Hello Mike! I find G503.com, CJ2A page and CJ3A&B...

    Hello Mike! I find G503.com, CJ2A page and CJ3A&B page to be very good sources of information. The thing to remember especially on the early trucks and flat fenders, poor record keeping and parts...
  22. Replies
    3
    Views
    145

    VT see if this discussion helps your decision. ...

    VT see if this discussion helps your decision.

    https://willysjeepforum.kaiserwillys.com/showthread.php?2888-Unleadead-fuel-in-your-Classic

    The most important thing to remember abut Ethanol is...
  23. Replies
    15
    Views
    358

    The fender I can see doesn't look too bad. I...

    The fender I can see doesn't look too bad. I would try to use the originals if you can. Nothing will fit like them on the original body. There are excellent reproduction parts out there also....
  24. Replies
    20
    Views
    829

    The rear support might be set up to fit all the...

    The rear support might be set up to fit all the CJ's, trim to fit. The early will be shorter than the later CJ's.
  25. Replies
    6
    Views
    340

    I have two of those Colman Camp stoves! What is...

    I have two of those Colman Camp stoves! What is it about cooking over white gas that makes food smell so good? You will use the heck out of the blasting cabinet. I have a similar one and an outdoor...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4