Search:

Type: Posts; User: Wulfie

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds; generated 12 minute(s) ago.

  1. Replies
    145
    Views
    39,465

    Wiggle , wiggle , wiggle

    Got the F 134 engine in , tight fit but can see why peeps cut out hood . Went ahead and installed The trans good thing i did , more alignment issues poped up. Guess i go back to the wiggling board....
  2. Replies
    145
    Views
    39,465

    When I was lining up body , i had the brake arm...

    When I was lining up body , i had the brake arm on but not the clutch arm . When i tried to put on clutch arm it seemed not to wanna line up right , looked to far towards the body center , looking...
  3. Thread: J300 done!

    by Wulfie
    Replies
    2
    Views
    2,467

    Congratulations for your success !

    Congratulations for your success !
  4. Replies
    145
    Views
    39,465

    Thanks guys . I know the F 134 sits higher than...

    Thanks guys . I know the F 134 sits higher than the L134 , was wondering where this difference comes from , is the head higher or the block itself or is the carburator the difference or some other...
  5. Replies
    145
    Views
    39,465

    Not planning to put F 134 engine in it , just...

    Not planning to put F 134 engine in it , just putting it in to check firewall clearence , by the way there are no holes in back of F 134 head or block to attach any linkage .
  6. Replies
    145
    Views
    39,465

    It fits !

    Things seem to be fitting up nicely , was kinda concerned after hearing other peoples experience with MD Juan bodies , but so far everything is fitting up pretty good . Bmorgil looks like even the...
  7. Replies
    145
    Views
    39,465

    Seems like your major problem with body fitting...

    Seems like your major problem with body fitting is the firewall to close to engine. I have a F 134 engine seized of course but was wondering if i can put in f 134 to se if everything fits up ok ....
  8. Replies
    145
    Views
    39,465

    The ross housing Im using is not the one Im gonna...

    The ross housing Im using is not the one Im gonna use. When I get the new steering worm shaft I will get it right . The one I did is just for moving it around. Ill check out your problems with...
  9. Replies
    145
    Views
    39,465

    Looking like a jeep

    Had one to press in the long one , but short one not so tight so I red lock tight it in . Sector shaft was very tight fit if not fit at all , so I lapped it in got it where it was free . I am close...
  10. Replies
    145
    Views
    39,465

    Yea well im gonna use it just for moving the...

    Yea well im gonna use it just for moving the frame around , plan to use new tube when it comes. Tnx LarrBeard and bmorgil . Machine shops around here hard to come by ,and the ones I have found really...
  11. Replies
    145
    Views
    39,465

    Worm steering transplant

    Well got most parts for steering except main thing ,. no shaft with wsorm gear , called KaiserWillys and had no clue when I would get it , but good thing part made in USA . So plan b . Cut off bad...
  12. Thread: The Frankenjeep

    by Wulfie
    Replies
    134
    Views
    213,792

    Good videos on youtube how to disssasemble t 18...

    Good videos on youtube how to disssasemble t 18 transfer case
  13. Replies
    145
    Views
    39,465

    Got him on his feet . Waiting on steering repair...

    Got him on his feet . Waiting on steering repair parts then move him out of shop and set body on him.
  14. Replies
    145
    Views
    39,465

    Yea , now i can move on . Finished brake plumbing...

    Yea , now i can move on . Finished brake plumbing today, gonna close up rear axle and put brakes and shoes on so he can stand up !
  15. Replies
    145
    Views
    39,465

    Will look for some grade eight washers , that...

    Will look for some grade eight washers , that kinda stuff hard to find in my town lol. Got 2 more shots for bmorgil's review . Drive side first , cost second. This after moving pinion in .002 ....
  16. Thread: Gear Pattern

    by Wulfie
    Replies
    1
    Views
    687

    Gear Pattern

    Will look for some grade eight washers , that kinda stuff hard to find in my town lol. Got 2 more shots for bmorgil's review . Drive side first , cost second. This after moving pinion in .002 ....
  17. Replies
    745
    Views
    221,761

    Always thought about welding a bunch of scrap...

    Always thought about welding a bunch of scrap iron and parts that i had laying around and calling it sculpture , would bring lots of money my way lol.
  18. Replies
    145
    Views
    39,465

    ROSS steering box

    Digging into ross steering box .Looks like complete re build . Steering tube cam has a notch in it and some rough ramps , bearings were all in the bottom of case ,shaft of the lever shaft was scored...
  19. Replies
    145
    Views
    39,465

    " S brake lines " and ball joints

    Question about "S" brake lines . Used the old ones if leaks cant stop , will put new ones on , thought it be easier to hook up originals . Also on steering rod ball joints castlated nuts to short ...
  20. Replies
    145
    Views
    39,465

    Raring to get UP !

    Got "RIPPER" up on his front 2 feet. Got the new rims , painted em up , been doing brake lines and finishing front hubs ,put steering rods on , and rippers two front teeth ,or zapats.
  21. Replies
    145
    Views
    39,465

    Wow the bag phone sure stirred up some noise lol.

    Wow the bag phone sure stirred up some noise lol.
  22. Replies
    145
    Views
    39,465

    Noticed that when I read the manual , but it is...

    Noticed that when I read the manual , but it is what it is ,still wish I had a bag phone . HI HO ,HI HO off to work we go , will shoot for 200 ft lbs . Tnx again bmorgil . I need a push once in...
  23. Replies
    145
    Views
    39,465

    Gonna do the best I can . Gonna do the pinion pre...

    Gonna do the best I can . Gonna do the pinion pre load to get approximately .030 rotational torque inch lbs , at 150 or more if you advise to do so. Tnx bmorgil . Means i gotta add shims to decrease...
  24. Replies
    145
    Views
    39,465

    Metalshaper checks his rotational torque at 100...

    Metalshaper checks his rotational torque at 100 ft lbs in his video on rear axle assembly .Should i be checking rotational torque at 150 ft lbs ? If so im not torqueing it enough to check rotational...
  25. Replies
    145
    Views
    39,465

    I only have it torqued to 100 ft lbs. The specs...

    I only have it torqued to 100 ft lbs. The specs say to torque pinion nut to 150 ft lbs minimum .
Results 1 to 25 of 113
Page 1 of 5 1 2 3 4