Search:

Type: Posts; User: Grouser

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    250

    It might be worth remotely mounting the oil...

    It might be worth remotely mounting the oil filter to avoid all the head bolt issues. Because if you have to retorque every head bolt three times you realize you'll have to pull the carburetor and...
  2. It's definitely a single wire alternator, there's...

    It's definitely a single wire alternator, there's only one Post in the back. I know what you're saying about the clip and multiple wires on the others. This was taken from another Parts jeep that I...
  3. head hurting a bit now..thsnks fire the help! So...

    head hurting a bit now..thsnks fire the help! So to review what you said I need to take the single wire from this alternator and run it to the positive post of the ammeter and then a wire from the...
  4. few and far between!!!

    few and far between!!!
  5. Thank you gentlemen. I had it all set up and...

    Thank you gentlemen. I had it all set up and ready to go it was out in less than 10 seconds only a few drops came out so I think I'm good have a great day
  6. when you change out the brake light sending unit,,,,do you need to bleed the brakes ?

    thanks for your help
  7. That's a good reads err! Thank you very much for...

    That's a good reads err! Thank you very much for your simplistic clarity. I am going from 6 volts to 12 volts and this alternator is a used one so I didn't have the instructions. Your instructions...
  8. Switching from a generator to an alternator, how to wire it.

    I've got one post on the back of the alternator. It says battery. Do I tie it into the wire that comes from the amp meter to the battery terminal of the old voltage regulator, and go to the battery...
  9. Replies
    3
    Views
    356

    That cleared things up gentleman thank you very...

    That cleared things up gentleman thank you very much have a great day
  10. Replies
    2
    Views
    293

    Thank you kindly sir

    Thank you kindly sir
  11. Replies
    3
    Views
    356

    How to plumb a heater on my cj3b

    So there's heater on the passenger side firewall with two tubes coming out of it one goes to the top of the water pump. Where does the other one go? And what do you think about Plumbing in a valve...
  12. Replies
    2
    Views
    293

    Inspection holes in bell housing

    I see two very large rectangular openings on each side of the bellhousing for inspection of the clutch and throwout bearing Etc. But are these things left uncovered all the time? Seems like some dirt...
  13. Replies
    1
    Views
    241

    Need an engine Rebuilder

    I have a block crank heads I want to buy an engine kit from Kaiser ,,,,where can I send it to for assembly,,,,,,
    anybody know? Looking for a crate motor or long block exchange type program thanks...
  14. Replacing the oil seals in the front axle cj3b

    So if I'm reading the book correctly the oil seals for the front axle on my cj3b it's a Dana 25, they are located inboard of the axle tubes near the third member. They have to be replaced after...
  15. Poll: I've done a helicoil before and they can be...

    I've done a helicoil before and they can be tricky. My main concern is the thickness of the material I'm trying to repair. I haven't been able to look at it close enough to tell but it seems like...
  16. Poll: The threads in the steering knuckle are stripped,,,

    Trying to rebuild the front of my cj3b and when I went to put the spindle back onto the steering knuckle one of the six bolts stripped out the threads in the housing. How hard is it to Helicoil? Or...
  17. Replies
    13
    Views
    3,618

    Where exactly are these seals located in the...

    Where exactly are these seals located in the axial? Time to replace mine and I don't see them.
  18. Can't find oil seals in front differential,

    Rebuilding the front axle on my 54 cj3b I've got the axles out and I'm trying to locate the inner oil seal. According to the book the service for the front axle is the same as the rear. I had no...
  19. Replies
    8
    Views
    727

    Wow bet we all learned something today. That kind...

    Wow bet we all learned something today. That kind of fixes all the problems right there. Thanks for the info man
  20. Replies
    8
    Views
    727

    sound good,,,, but was asked if I knew the parts...

    sound good,,,,
    but was asked if I knew the parts I was using were compatible with silicone fluids,,,,
    is that an issue with this older equipment?
  21. Replies
    8
    Views
    727

    If the silicone doesn't add to the survivability...

    If the silicone doesn't add to the survivability or corrosion resistance or anything else like that I agree. Thanks for your help that was a great read.
  22. Replies
    8
    Views
    727

    Which brake fluid do I choose?

    Restoring my 54 Willys Jeep. All new brake lines Master cylinder wheel cylinders everything. Four-wheel drum brakes so heat shouldn't be a problem. Just wondering since I have the opportunity to use...
  23. hahaha lol

    hahaha lol
  24. Look at these worn hanger bolts

    Both of them on the rear front or worn through the bronze bushings and through the first Leaf of the spring. That could have been ugly out on the road at highway speed. But I got it all fixed now...
  25. Got it I let it set overnight and got a bigger...

    Got it I let it set overnight and got a bigger Hammer that seemed to work.
Results 1 to 25 of 38
Page 1 of 2 1 2