Search:

Type: Posts; User: bmorgil

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    65

    I think you are saying, with the blazing top...

    I think you are saying, with the blazing top speeds and precise road feedback provided by the early Willys, the effect of a good set of trued and balanced tires is un-dectectable.
  2. Replies
    8
    Views
    65

    The intake manifold and exhaust manifold are...

    The intake manifold and exhaust manifold are worth $150 at least. The starter and carb bring a bunch more. As LarrBeard alluded to, it looks like a great re-builder.
  3. Replies
    2,025
    Views
    279,348

    I like your thought process. Once you get it...

    I like your thought process. Once you get it cleaned off it should be easier to tell where its coming from.

    If you go after the rear diff cover, use the Fel-Pro gasket Part # RDS 6095-1. On the...
  4. Replies
    2,025
    Views
    279,348

    This is a picture of a REAL bad grove. I don't...

    This is a picture of a REAL bad grove. I don't like to see much of a grove at all. Any pits or anything that is other than perfectly smooth, will just cut up the new seal or leak under the lip.
    ...
  5. Replies
    22
    Views
    1,461

    Drop an email to amy@kaiserwillys.com She is...

    Drop an email to amy@kaiserwillys.com She is awesome. She will move the thread for you.
  6. Replies
    2,025
    Views
    279,348

    I loved reading your reply about the match! It...

    I loved reading your reply about the match! It fits in great with the American Rifleman story this month about the Springfield sniper rifles. It is amazing what YOU can do with a rifle designed over...
  7. Looking good! As for the device, I am in for...

    Looking good!

    As for the device, I am in for take it out. I have to agree with LarrBeard, the contraption cannot be of benefit to airflow.
  8. Replies
    2,025
    Views
    279,348

    Wow would that be cool! A chance to learn from...

    Wow would that be cool! A chance to learn from the very best.
  9. I can't wait to hear what that might be. It does...

    I can't wait to hear what that might be. It does look like some type of pre-heat device.
  10. Thread: 1963 Willy’s

    by bmorgil
    Replies
    5
    Views
    105

    Welcome and thank you for your service! It is...

    Welcome and thank you for your service! It is starting to snow here in Northern Ohio. I understand "down for the winter". My son and his friends are just getting their Jeeps out, I am stashing mine...
  11. Replies
    2,025
    Views
    279,348

    Correct, it will only go back in one way. ...

    Correct, it will only go back in one way.

    Thank you for your continued service to our Freedom and Country Ira!
  12. Replies
    6
    Views
    242

    Again it all depends on application. In the case...

    Again it all depends on application. In the case of some of the rear axle bearings on the Timken and the Dana used in the Williys, they are shimmed in and out for proper end play. It is essential...
  13. Replies
    6
    Views
    242

    No problem!

    No problem!
  14. Replies
    6
    Views
    242

    Some bearing cup rotation is allowed. The Cups...

    Some bearing cup rotation is allowed. The Cups need to be able to move in and out for adjustment. Clean the axle bores and the cups should be a very nice slide in fit. As you shim the axles in and...
  15. Thread: Loose lug nuts

    by bmorgil
    Replies
    6
    Views
    246

    If the lug nuts are OK, It is possible someone...

    If the lug nuts are OK, It is possible someone replaced the studs and didn't get them seated all the way. Are you using a torque wrench? Make sure you actually torque the nuts to spec. There are two...
  16. Replies
    6
    Views
    163

    Grouser, I agree with gmwillys, no big deal. I...

    Grouser, I agree with gmwillys, no big deal. I will say however, the best way would be to pull the front and rear driveshaft.
  17. Thread: Loose lug nuts

    by bmorgil
    Replies
    6
    Views
    246

    Are the rims the stock steel?

    Are the rims the stock steel?
  18. Replies
    2,025
    Views
    279,348

    Just think of how much you know about those...

    Just think of how much you know about those brakes being able to slow you down quickly from 60. That will keep you honest!
  19. Replies
    71
    Views
    2,642

    You need a Fabrication guy.

    You need a Fabrication guy.
  20. Replies
    2,025
    Views
    279,348

    Use a Fel-Pro on the valve cover. VS 6617 C

    Use a Fel-Pro on the valve cover. VS 6617 C
  21. Replies
    4
    Views
    364

    Nice 3A! More pictures!

    Nice 3A! More pictures!
  22. Replies
    11
    Views
    624

    I assume you are referencing the whopping 45 HP...

    I assume you are referencing the whopping 45 HP of the VW. If you are taking it to Moab, Yup about 50 all the way is comfy. Though the little air cooled 4 was not very strong the gearing lets it self...
  23. Replies
    12
    Views
    731

    Thanks! Perfect pictures. The drive line you have...

    Thanks! Perfect pictures. The drive line you have would help out a lot of the people who have the old style Detroit. I can now clearly see how it is set up.
    Thanks for the shots!
  24. Mark, there are stainless lines available....

    Mark, there are stainless lines available. https://www.inlinetube.com/products/sjpb6001

    There is a custom stainless bender up in the Detroit area. I can look for his info if you want it. It's...
  25. Replies
    6
    Views
    506

    Man somebody got a nice one!

    Man somebody got a nice one!
Results 1 to 25 of 488
Page 1 of 20 1 2 3 4