Search:

Type: Posts; User: gmwillys

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    40

    The rig isn't in too bad of condition, but there...

    The rig isn't in too bad of condition, but there was a design flaw that carries on to this day. The frames do not have any real drainage holes. This frame was packed full of mud in the areas of rot.
  2. Replies
    5
    Views
    40

    Day 1. Pull the fuel tank and check the inner...

    Day 1. Pull the fuel tank and check the inner frame and crossmembers. Pull the front bumper off, and check out the front frame rails. The passenger side was damaged, and the driver's side was soft...
  3. Replies
    5
    Views
    40

    Another Heep project

    There is no wonder to why don't get anything finished. I have taken on yet another Heep project. This one should be a fairly quick turnaround, but who am I fooling. At least it runs, drives, and...
  4. Replies
    8
    Views
    165

    Good tires, (or even a matching set) are...

    Good tires, (or even a matching set) are overrated. On second thought, don't follow my poor example.
  5. Replies
    8
    Views
    165

    I had seen the add on eWillys.com this morning. ...

    I had seen the add on eWillys.com this morning. There is enough goods there to feel pretty confident that it would be a wise purchase. A Carter carb and a starter are pluses. The main thing about...
  6. Replies
    22
    Views
    1,527

    Practice, practice, practice. I use a Miller 175...

    Practice, practice, practice. I use a Miller 175 110 volt MIG, and run .035 solid wire, and 75/25 Argon gas. The .035 wire does real well in filling holes and controlling heat. The biggest thing...
  7. Replies
    2,040
    Views
    280,545

    Pelago, Remember you just had your Jeep...

    Pelago,

    Remember you just had your Jeep serviced. A Willys will leak until it finds its happy place for fluid levels. If the service station pumped in dope until it was running out the hole,...
  8. Replies
    2,040
    Views
    280,545

    I'd love to sit through one of your courses. I'd...

    I'd love to sit through one of your courses. I'd like to be better than an alright shot.
  9. Replies
    5
    Views
    142

    Welcome Brian!

    Welcome Brian!
  10. I second the J.C. Whitney miracle fuel miser flux...

    I second the J.C. Whitney miracle fuel miser flux capacitor theory.
  11. Welcome icetime33, That looks to me that the...

    Welcome icetime33,

    That looks to me that the item shown is a high idle mechanism for extreme Arctic temps? I'll have to research this a bit further. What's the model and make on the carb?
  12. Welcome Michigan willys, Check out...

    Welcome Michigan willys,

    Check out eWillys.com,. David Eighlers who runs the site has been working on gathering information on hard tops for Willys. In turn, he has been gathering classified ads...
  13. Replies
    2,040
    Views
    280,545

    I recommend the following book that covers the...

    I recommend the following book that covers the very topic you are talking about;

    https://www.amazon.com/Silence-War-Marine-Young-Marines/dp/1101988185

    Maybe there are some avenues that you can...
  14. Replies
    5
    Views
    139

    Welcome Kev1963, Thank you for your service! ...

    Welcome Kev1963,

    Thank you for your service!

    Great looking CJ5! We look forward to helping out on your journey.
  15. Replies
    1
    Views
    101

    Welcome JJ0225, It has been done before...

    Welcome JJ0225,

    It has been done before without chopping through the hood. Some have gone with a body lift to gain clearance, while others have fabricated a new air horn to make the needed room.
  16. Replies
    2,040
    Views
    280,545

    Goodnight Chesty, wherever you are. Happy...

    Goodnight Chesty, wherever you are. Happy birthday!
  17. Replies
    71
    Views
    2,737

    Amén on your salute to our Veterans. It helps...

    Amén on your salute to our Veterans.

    It helps to keep close tabs on your builds. Photo and serial numbers recorded are great to file away just in case something were to happen to your truck.
  18. Replies
    2,040
    Views
    280,545

    Thank you to all Veterans! Great job on...

    Thank you to all Veterans!

    Great job on pulling through the hardships to get Magoo to this point. Mr. Magoo would have been proud to ride shot gun with you on your first parade.
  19. Replies
    71
    Views
    2,737

    People are starting to see the beauty of these...

    People are starting to see the beauty of these Gladiators. The Jeep Commandoes are starting to gain traction for the next popular builds, especially the Hurst version.
  20. Replies
    6
    Views
    231

    We look forward to following your progress!

    We look forward to following your progress!
  21. Replies
    6
    Views
    198

    You won't have any issues. Just check all your...

    You won't have any issues. Just check all your differentials for oil, shoot a little grease in the axle bearing zerks, and stop to check hub temperatures from time to time. All will be OK.
    ...
  22. Replies
    6
    Views
    198

    I've spent some time this morning trying to find...

    I've spent some time this morning trying to find an article that I had come across on converting the rear axle to accepting a lock out hub. I know it's out there in space, and will continue to look...
  23. Replies
    2,040
    Views
    280,545

    Mount the placard, I doubt the Major General is...

    Mount the placard, I doubt the Major General is still looking for it.
  24. Replies
    2,040
    Views
    280,545

    Good boy! He's getting big.

    Good boy! He's getting big.
  25. Thread: Scraping

    by gmwillys
    Replies
    10
    Views
    681

    Sometimes you have to slow down to speed up... ...

    Sometimes you have to slow down to speed up... No removers used.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4