Search:

Type: Posts; User: bmorgil

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2,122
    Views
    290,554

    The Tightsteer is to help with a worn sector...

    The Tightsteer is to help with a worn sector shaft thrust surface. You will know if you have a problem with this with a visual inspection. First you must be sure the steering box is in the center of...
  2. Replies
    2,122
    Views
    290,554

    Nice and, permanant! Coffee and bourbon always...

    Nice and, permanant!

    Coffee and bourbon always both!
  3. Replies
    2,122
    Views
    290,554

    The Pertronix

    One thing to add... On the Pertronix ignition, there is an Ignitor and an Ignitor II. These ignitions use a magnetically switched trigger (not a magnetic pulse). This has a majior advantage and a...
  4. Replies
    2,122
    Views
    290,554

    There is no arguing your point on the "Points"...

    There is no arguing your point on the "Points" gmwillys! To add to that, in the event of a HPEM the points will keep running! With the Pertronix the whole thing replaces the points plate. You even...
  5. Replies
    82
    Views
    3,641

    Ha ha! I love the nostalgia of the whole thing....

    Ha ha! I love the nostalgia of the whole thing. That is going to be a sweet ride with air, cruisin' through the Pima McDonald's that's for sure. I think gmwillys has had some bad experiences with...
  6. Replies
    2,122
    Views
    290,554

    The wheel shimmy could be a few things. Tire...

    The wheel shimmy could be a few things. Tire balance will cause it. On a front drive/steer axle like the Willys, often it is the steering knuckle pivot bearings. If the preload gets too loose on the...
  7. Thread: 1957 cj-5

    by bmorgil
    Replies
    7
    Views
    235

    You've made some great decisions on the project...

    You've made some great decisions on the project okiemark. I am happy with the body kit from KW on my CJ3A. It did need some work to make it fit. I wrote about some difficulties I had with mine. I...
  8. Replies
    2,122
    Views
    290,554

    Last time? You mean on this go round I take it!...

    Last time? You mean on this go round I take it! It is a very old Willys, it may need you from time to time!
  9. Replies
    2,122
    Views
    290,554

    You can't get any better than that!

    You can't get any better than that!
  10. Replies
    2,122
    Views
    290,554

    I think the hope was the transfer case would...

    I think the hope was the transfer case would block everything? Well it looks like you are almost ready for a test ride.
  11. Thread: 1957 cj-5

    by bmorgil
    Replies
    6
    Views
    207

    Picture okiemark.

    Picture okiemark.
  12. Thread: 1957 cj-5

    by bmorgil
    Replies
    6
    Views
    207

    If it is on the side of the tube, it is probably...

    If it is on the side of the tube, it is probably for the brake line tee bolt.
  13. Replies
    2,122
    Views
    290,554

    It is chapter 6 in the Military Manual. It starts...

    It is chapter 6 in the Military Manual. It starts on page 114. https://documentcloud.adobe.com/link/track?uri=urn%3Aaaid%3Ascds%3AUS%3Acc44df5e-b547-48b1-9929-f4861a344c4d If this isn't what you...
  14. Replies
    2,122
    Views
    290,554

    I hate that when the thoughts creep in. Well lets...

    I hate that when the thoughts creep in. Well lets hope for no leaks. My brother calls these 15 minute projects. Projects that turn into monumental events!
  15. Thread: 1957 cj-5

    by bmorgil
    Replies
    6
    Views
    207

    It is probably for a vent. Send a pic.

    It is probably for a vent. Send a pic.
  16. The concern is on the drive side of the gears....

    The concern is on the drive side of the gears. That is the convex side on the ring gear. That side should be the one that tells the story. The drive side of the pinion is a little blurry in the...
  17. Replies
    2,122
    Views
    290,554

    I think you are saying that you will have .005"...

    I think you are saying that you will have .005" of end play. That's pretty good.
  18. Replies
    2,122
    Views
    290,554

    The lip goes towards the oil. The oil pushes...

    The lip goes towards the oil. The oil pushes against the lip pushing it down making a better seal. If it was lip out it would be too easy for the oil to leak out.
  19. Replies
    2,122
    Views
    290,554

    TM9-8015-2: Power Train Body and Frame manual

    The military manual (TM-8015-2) is posted on this site here.
    ...
  20. Thread: 1957 cj-5

    by bmorgil
    Replies
    7
    Views
    235

    A CJ5 with some nice tires has always been a cool...

    A CJ5 with some nice tires has always been a cool looking rig! Good luck on the find! What motor do you have?
  21. Replies
    17
    Views
    564

    It is coming back! What do you use for a face...

    It is coming back!

    What do you use for a face mask so you can breath while the dust is flying? Everything I try fog's my safety glasses.
  22. Replies
    2,122
    Views
    290,554

    Let me know how it goes , I'll be standing by.

    Let me know how it goes , I'll be standing by.
  23. Replies
    2,122
    Views
    290,554

    You shouldn't need to get to the bearing....

    You shouldn't need to get to the bearing. Assemble it with no sealant on the shims then check the end play like they show in the Novack Guide. When you are confident there is more than .002" and less...
  24. Replies
    2,122
    Views
    290,554

    It's not as bad as it seems. It is important for...

    It's not as bad as it seems. It is important for the life of the transfer case to get it right.

    The Novak Guide here does a good job. ...
  25. Replies
    2,122
    Views
    290,554

    The below is from the Novac Guide. It is pretty...

    The below is from the Novac Guide. It is pretty good. http://www.novak-adapt.com/knowledge/transfer-cases/rebuild-guides/dana-18-rebuild-guide

    Output Shaft Endplay
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4