Search:

Type: Posts; User: test1328

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    136

    That is pretty awesome! I'm not familiar with...

    That is pretty awesome! I'm not familiar with this model, so have a few questions:
    1. Which lights do the three lever light switch control and why are they located where they are instead of...
  2. Replies
    155
    Views
    14,277

    Much appreciated input, guys. I've never seen...

    Much appreciated input, guys. I've never seen anything talking about lube for the carburetor either, but with my carb rebuild, a lot of the parts that move feel dry. I know gas will lubricate some...
  3. Replies
    155
    Views
    14,277

    No one has an opinion?

    No one has an opinion?
  4. Replies
    24
    Views
    740

    I tend to agree with bmorgil that it looks like...

    I tend to agree with bmorgil that it looks like the PTO control. I'm not familiar at all with the Tuxedo Park rigs, but my CJ has the PTO control on the center floor just behind the transmission...
  5. Replies
    155
    Views
    14,277

    Quick question, guys. I am in the process of...

    Quick question, guys. I am in the process of cleaning and rebuilding the carburetor and got to wondering about lubrication for the various parts that need to rotate, like the rods that the butterfly...
  6. Replies
    24
    Views
    740

    Sounds like you have a plan, Cat! I have a Ford...

    Sounds like you have a plan, Cat!
    I have a Ford pickup of similar vintage. Mines a 1990 F250 that I bought new and have used on a lot of hunting trips. Here's a recent picture of it transporting...
  7. Replies
    24
    Views
    740

    Hey Cat, nice jeep. I'm sure you'll have a blast...

    Hey Cat, nice jeep. I'm sure you'll have a blast getting her up and running again.

    I just woke my CJ5 up from slumber since 88. Fortunately for me it wasn't very difficult to get her started. ...
  8. Replies
    155
    Views
    14,277

    Got my engine delivered to the rebuilder a week...

    Got my engine delivered to the rebuilder a week ago on 12/27. Said is should take about 8 weeks.

    I've started to rebuild the carb in the meantime and have it all taken apart and ready to clean. ...
  9. Replies
    155
    Views
    14,277

    HA! Yes, I agree! Oil and grease would...

    HA! Yes, I agree! Oil and grease would definitely be better. I did take a closer look at the bell housing a few days ago and it doesn't appear to be bad at all. Should clean right up, I think.
  10. Replies
    155
    Views
    14,277

    Thanks, bmorgil. I suppose I didn't explain...

    Thanks, bmorgil. I suppose I didn't explain myself well enough regarding the pressure plate adjustment. What I was meaning was that in the manual they go into great detail about adjusting the...
  11. Replies
    155
    Views
    14,277

    I received the clutch kit yesterday, so I'll take...

    I received the clutch kit yesterday, so I'll take the pertinent parts down with me when I deliver the motor so that they can balance everything with the clutch plate attached. I also ordered the...
  12. Replies
    155
    Views
    14,277

    Thanks, LarrBeard. You're right about not...

    Thanks, LarrBeard. You're right about not appreciating how many problems you can avoid by doing things right the first time. I did look at the Bendix gear when I took the starter out and it is worn...
  13. Replies
    155
    Views
    14,277

    Thanks for the replies, guys. I'm definitely not...

    Thanks for the replies, guys. I'm definitely not going to cut corners at this point. Don't want to leave anything to chance unless it is something the is easily replaced and fixed, i.e. easy access.
  14. Replies
    155
    Views
    14,277

    Just for the record, I thought I would show how I...

    Just for the record, I thought I would show how I rigged up the engine for transport to the rebuilder. It is actually quite stable. I added another strap across the front of the engine that isn't...
  15. Replies
    155
    Views
    14,277

    Here's a closeup of the flywheel. Is there any...

    Here's a closeup of the flywheel. Is there any reason that I shouldn't try to replace the ring gear on this now? Looks fairly worn to me.

    8958
  16. Replies
    155
    Views
    14,277

    Thanks for the tips. I'll be sure and address...

    Thanks for the tips. I'll be sure and address the surfacing of the flywheel with the engine rebuilder when I get there. If he isn't planning on doing it, then I'll make sure I take care of it.
  17. Replies
    155
    Views
    14,277

    Thanks for the quick replies, guys. I laughed...

    Thanks for the quick replies, guys. I laughed about blowing out the bell housing with compressed air, gm. Take a look at this picture that shows what the bell housing looks like. It is so full of...
  18. Replies
    155
    Views
    14,277

    I am happy to report that I have successfully...

    I am happy to report that I have successfully removed the engine!

    8939

    Now I have more questions, of course!

    I want to get a new clutch to install. On the Kaiser Willys website they show a...
  19. Replies
    155
    Views
    14,277

    I've been debating about whether to start a new...

    I've been debating about whether to start a new thread on this project since we've kind of gotten through the restart info and what needs to be done to remove the engine...what do you think? Should...
  20. Replies
    155
    Views
    14,277

    Looks good to me!

    Looks good to me!
  21. Replies
    155
    Views
    14,277

    OK. Sounds good. Yes, this 134 engine does have...

    OK. Sounds good. Yes, this 134 engine does have the fixed skid plate on the oil pan. I'll fab up some blocking to support the engine to keep it upright as you suggest.

    Thanks!
  22. Replies
    155
    Views
    14,277

    Thanks! Once again, great info for a newbie. ...

    Thanks! Once again, great info for a newbie.

    I'm picking up an engine hoist from a friend tomorrow and then I should be ready to pull the engine after I take out the last remaining bell housing...
  23. Replies
    155
    Views
    14,277

    Thanks for the info and links. Much appreciated.

    Thanks for the info and links. Much appreciated.
  24. Replies
    155
    Views
    14,277

    I hate to keep asking questions, but I really do...

    I hate to keep asking questions, but I really do appreciate everyone's knowledge and expertise here. The information in invaluable. Don't know where else I would even dream of finding this...
  25. Replies
    155
    Views
    14,277

    Thanks for everyone's thoughts on including the...

    Thanks for everyone's thoughts on including the distributor with the engine for the rebuild. I'll be sure to do that. Much appreciated.
Results 1 to 25 of 66
Page 1 of 3 1 2 3