Search:

Type: Posts; User: bmorgil

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1,036
    Views
    481,185

    I cant wait to watch this one grow!

    I cant wait to watch this one grow!
  2. Thread: Steering

    by bmorgil
    Replies
    1
    Views
    31

    Not really. You might be able to take out a very...

    Not really. You might be able to take out a very small amount but you will run into the stops on the sector shaft on full turns. The high point is adjusted at assembly and isn't really a wear...
  3. Thread: Running to hot

    by bmorgil
    Replies
    3
    Views
    45

    Steve what do the plugs look like? Is it steaming...

    Steve what do the plugs look like? Is it steaming them? Is there white steam in the exhaust? If the head gasket is blown there should be bubbles in the water in the radiator when the engine is...
  4. Replies
    3
    Views
    38

    That's a nice looking Jeep! It is certainly all...

    That's a nice looking Jeep! It is certainly all there. I will tell you nothing will come in more handy than the service manual when it comes to working on your brakes.
  5. Replies
    267
    Views
    27,250

    I was thinking some 24's so you could strap on...

    I was thinking some 24's so you could strap on some Mickey Thompson Baja Pro XS 21/58-24LT's! The 58" diameter should give you adequate ground clearance.
    ...
  6. Sorry about that Wulfie, I should have clarified...

    Sorry about that Wulfie, I should have clarified that! All of the weight sits on the top rubber on top of the cross member. Here is a photo from underneath (its blurry I couldn't hold still standing...
  7. Replies
    4
    Views
    108

    I can see it is getting quite a notch worn into...

    I can see it is getting quite a notch worn into it at the one end. I would say time to replace that one
  8. Mike, The Willys F4-134 was introduced in 1950....

    Mike, The Willys F4-134 was introduced in 1950. It was in civilian Jeeps, CJ-3B, CJ-5, and CJ-6 models. It was also used in the Willys 473 and 475 pickups, wagons, and sedan deliveries. If you have a...
  9. Here is a pic of how it goes. Everything sets on...

    Here is a pic of how it goes. Everything sets on the cross member and the bolt goes through the cross member.

    9388
  10. Replies
    160
    Views
    41,728

    Looking good Joey!

    Looking good Joey!
  11. Replies
    17
    Views
    710

    The exact tray might be tough to find, but I used...

    The exact tray might be tough to find, but I used one of these.

    https://www.kaiserwillys.com/nsearch/?q=battery%20tray
  12. Replies
    32
    Views
    1,529

    I would just use the block. Rebuild it as if it...

    I would just use the block. Rebuild it as if it was a Willys 134. Have the shop use the WIllys parts and the new block. It is possible there are different components in the engine. If the valves are...
  13. Replies
    267
    Views
    27,250

    Definitely the part that separates the men from...

    Definitely the part that separates the men from the boys. The turbo plumbing is artwork.
  14. Replies
    4
    Views
    108

    VT I would start by trying to adjust the clutch...

    VT I would start by trying to adjust the clutch free play. They don't need much. Just a half inch at the pedal should be a good place to start. If you cant get the free play correct, the linkage...
  15. Hello Mike! I find G503.com, CJ2A page and CJ3A&B...

    Hello Mike! I find G503.com, CJ2A page and CJ3A&B page to be very good sources of information. The thing to remember especially on the early trucks and flat fenders, poor record keeping and parts...
  16. Replies
    3
    Views
    115

    VT see if this discussion helps your decision. ...

    VT see if this discussion helps your decision.

    https://willysjeepforum.kaiserwillys.com/showthread.php?2888-Unleadead-fuel-in-your-Classic

    The most important thing to remember abut Ethanol is...
  17. Replies
    15
    Views
    307

    The fender I can see doesn't look too bad. I...

    The fender I can see doesn't look too bad. I would try to use the originals if you can. Nothing will fit like them on the original body. There are excellent reproduction parts out there also....
  18. Replies
    17
    Views
    710

    The rear support might be set up to fit all the...

    The rear support might be set up to fit all the CJ's, trim to fit. The early will be shorter than the later CJ's.
  19. Replies
    6
    Views
    312

    I have two of those Colman Camp stoves! What is...

    I have two of those Colman Camp stoves! What is it about cooking over white gas that makes food smell so good? You will use the heck out of the blasting cabinet. I have a similar one and an outdoor...
  20. Thread: New Here

    by bmorgil
    Replies
    3
    Views
    68

    Welcome aboard!

    Welcome aboard!
  21. Replies
    15
    Views
    307

    CaptB, a great start for a restore! Man it looks...

    CaptB, a great start for a restore! Man it looks really complete. The top is a very nice thing to have. That CJ should restore like new.
  22. Replies
    35
    Views
    3,435

    Nice! Sounds like a perfect day working on the...

    Nice! Sounds like a perfect day working on the Willys. Hang on to that tag. You can buy a new rivit online.
  23. Replies
    267
    Views
    27,250

    Compound turbo's are definitely a modern hot rod...

    Compound turbo's are definitely a modern hot rod diesel thing. Looks right at home in that '56 in a Mad Max sort of way!
  24. Replies
    84
    Views
    95,444

    Uncovering the past history is one of the fun...

    Uncovering the past history is one of the fun parts of these things.
  25. Replies
    9
    Views
    305

    I found it very difficult to find a radiator shop...

    I found it very difficult to find a radiator shop also. No one works on them anymore. For decades they have been plastic and aluminum, glued and crimped and not repairable.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4