Page 73 of 252 FirstFirst ... 2363717273747583123173 ... LastLast
Results 721 to 730 of 2512

Thread: well, the darn thing is out

  1. #721
    Senior Member pelago's Avatar
    Join Date
    May 2016
    Location
    easter north carolina
    Posts
    1,261
    Quote Originally Posted by gmwillys View Post
    That will be an easy fix. Just look at the yoke's sealing surface for any grooves worn into the sealing surface. If no grooves or pits are seen, put you a new seal in, and you'll be good to go. Make sure that none of the gear lube got on the parking brake shoes. If it did, clean well with brake cleaner. If it was the service brakes, then they would have to be replaced, because you can never fully get the lube out of the shoe linings.

    You'll get to the body soon enough. Once you do, and get the hang of rust repair, it will all come together fairly quickly. You will be painting by fall.
    Transfer - Exploded.jpgtransfer case.jpg

    are we talking about item Nr 1 in larger photo?

  2. #722
    Senior Member pelago's Avatar
    Join Date
    May 2016
    Location
    easter north carolina
    Posts
    1,261
    Grrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrr............. ...........

  3. #723
    Senior Member pelago's Avatar
    Join Date
    May 2016
    Location
    easter north carolina
    Posts
    1,261
    putting it down for a while before i get mad at it and hurt it

  4. #724
    Senior Member
    Join Date
    Jan 2015
    Posts
    184
    Number one would be the culprit if it is grooved where the seal rides. Had to order a couple of yokes for mine. I read somewhere there is a ready sleeve (or redi-sleeve?) kit available to do a repair if desired but I donít have specific info for that.
    Jeff
    '51 CJ3A
    '47 CJ2A

  5. #725
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    2,496
    Speedy sleeve, is what we always called it. On heavy dirt equipment, a lot of the crank shaft front seals would get grooved up with dirt intrusion. The speedy sleeves work well. The sleeve bonds to the crank surface, and the seal rides on the sleeve.

  6. #726
    Senior Member pelago's Avatar
    Join Date
    May 2016
    Location
    easter north carolina
    Posts
    1,261
    Gear box almost assembled...
    Have the center rod that trips the switch, then the cap/race then the spring then the piece the screws into the rod, then the cap...
    Aint no way that i can figure out how to get that cap on top of the tubing??? Not unless i destroy it.. Darned camera somehow does not want to send photos to my email so i can save em and post here

    found out why the top bearing will not go in and catch, it is our of round and not sure if i want to try and repair?? called mike they are sending another under warranty. good place
    Last edited by pelago; 07-06-2018 at 04:36 PM.

  7. #727
    Senior Member pelago's Avatar
    Join Date
    May 2016
    Location
    easter north carolina
    Posts
    1,261
    DRAG LINK.jpg

    this is rather interesting, wonder why one end assembled different from other end

  8. #728
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    2,496
    That is a good question. I've never noticed a difference in the parts when removing them. I don't think I've ever seen two item 'C' on one end. Ponderous.

  9. #729
    Senior Member pelago's Avatar
    Join Date
    May 2016
    Location
    easter north carolina
    Posts
    1,261
    happen to have two of them only taken one apart. pretty ucky, however it was like the diagram. so guess it is correct,. but, seems to stupid old me just more parts to have to stock somewhere where same parts on either end would work fine(but maybe they dont work fine and someone found that out) so, i re assembled it according to diagram and will put on soon. The rebuild kit i got is complete with all new pieces and parts, with exception of grease fittings

  10. #730
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    2,496
    Grease zerks are easy to come by. Napa should have all that you need.

    I can say I learned something today, about the drag link.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •