Page 98 of 252 FirstFirst ... 488896979899100108148198 ... LastLast
Results 971 to 980 of 2512

Thread: well, the darn thing is out

  1. #971
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    3,570
    There is a panel you are missing ties into the top panel you have in place, (where the starter button is affixed). The lower section fills the remainder of the hole sans the transmission top cover. Essentially there are three pieces in total for the center. With the three pieces removed, it made engine and transmission access easy. This also allows the body to be removed without removing the steering wheel. I'll look around to see if there are any reproductions or descent used ones are available.

    There is also a cover that covers the passenger floor toe board. This one allows access to the heater core if equiped from the top side. I'll get you some pictures early in the AM.
    Last edited by gmwillys; 11-14-2018 at 08:52 PM.

  2. #972
    Senior Member pelago's Avatar
    Join Date
    May 2016
    Location
    easter north carolina
    Posts
    1,261
    pictures early in the AM. thanks trying to describe what i need to mike at kaiser not easy considering he deals with all of the jeeps even sent a photo to him

  3. #973
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    3,570
    I fouled up my explanation. I fixed it so it makes more sense.

    I found one lower transmission cover on eBay. It is an NOS, and $125.00. They are proud of them. While looking, there was one heater core inspection cover for $9.99.
    Last edited by gmwillys; 11-14-2018 at 08:51 PM.

  4. #974
    Senior Member pelago's Avatar
    Join Date
    May 2016
    Location
    easter north carolina
    Posts
    1,261
    Got this coming.....FLOOR SECTIONII.jpg


    its one hell of a start in filling that hole up

  5. #975
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    3,570
    That's what you needed. Did Mike have one?

  6. #976
    Super Moderator LarrBeard's Avatar
    Join Date
    Nov 2014
    Location
    Ft. Wayne, IN
    Posts
    2,482
    The good news is that the piece fills a lot of the hole at one time...

  7. #977
    Senior Member pelago's Avatar
    Join Date
    May 2016
    Location
    easter north carolina
    Posts
    1,261
    no he wanted me to buy a whole new floor at 1000.00

  8. #978
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    3,570
    $1,000 is a bit much on an entire floor. You did well. I thought I had more pictures of the covers, but no. This one will give you the general idea.
    Attached Images Attached Images

  9. #979
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    3,570
    I forgot I had pictures from the M38 that I had. The layout is much the same as the A1. The sides of the lower cover was glassed over, so the bolt holes were not visible. That was the strange part of this M38. The floors were not in bad condition, but there was a thick layer of fiberglass slathered over the whole floor. I did notice that I had the master cylinder cover turned the wrong direction. The flat edge is supposed to be against the edge of the throttle mount bulge. The last picture was a make a like aftermarket body. It was a bastardization of a CJ and a M38, but it did have the military style trans cover.
    Attached Images Attached Images
    Last edited by gmwillys; 11-15-2018 at 08:08 AM.

  10. #980
    Senior Member pelago's Avatar
    Join Date
    May 2016
    Location
    easter north carolina
    Posts
    1,261
    and will still need this, seen lots of different prices on same item688966_d.jpg


    and my gas tank area quite rough but also seen some good prices on replacements for that, getting happier with the floor section working it in. right rear fender well going to be a challenge whole lot of welds

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •