Page 1 of 3 123 LastLast
Results 1 to 10 of 22

Thread: Champion Radiator in a CJ3A

Hybrid View

  1. #1
    Senior Member bmorgil's Avatar
    Join Date
    Dec 2018
    Location
    Northwestern Ohio
    Posts
    350

    Champion Radiator in a CJ3A

    A few shots of a champion radiator with the original fan shroud mounted. The Radiator had to be spaced out 1/2" closer to the motor, or it hits the front cross member and would set to high. Not a big deal. It does put the fan closer to the generator/alternator pulley. On mine, I had to trim it a bit. The fan also contacted the bottom of the shroud slightly. There was minimal trimming on the bottom of the shroud. The fan fits in nicely and pulls air quite well. This should be a very efficient cooling system.
    Attached Images Attached Images

  2. #2
    Super Moderator LarrBeard's Avatar
    Join Date
    Nov 2014
    Location
    Ft. Wayne, IN
    Posts
    1,131
    Very nice setup!

  3. #3
    Senior Member bmorgil's Avatar
    Join Date
    Dec 2018
    Location
    Northwestern Ohio
    Posts
    350
    Thanks LarrBeard! Means a lot coming from you!!

  4. #4
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    1,676
    Looks great! You might need to draw everything out as a how too for anyone else who is considering the conversion.

  5. #5
    Senior Member TJones's Avatar
    Join Date
    Apr 2018
    Location
    Akron, Ohio
    Posts
    232
    I called Ledfoot Racing in California yesterday and asked if could modify the radiator for my Heep and they told me to contact Champion directly, Ledfoot is just a dealer for Champion.
    He gave me there number and it’s “Champion Cooling Systems” and the girl that I talked to was Very helpful, she said they can build anything I wanted. She said just email me a diagram of what I needed and they would send me a price to build it!!!!
    On my way to FANCY....Maybe...I haven’t seen the price tag yet
    Last edited by TJones; 07-02-2019 at 07:05 AM.

  6. #6
    Senior Member bmorgil's Avatar
    Join Date
    Dec 2018
    Location
    Northwestern Ohio
    Posts
    350
    I am going to say they will be reasonable. From what I can tell their direct interaction with a customer, documented on a forum, resulted in a darn good radiator for my CJ3A.

    It is a fantastic thing when you get linked up with a source for something, from a customer focused entity!

  7. #7
    Senior Member TJones's Avatar
    Join Date
    Apr 2018
    Location
    Akron, Ohio
    Posts
    232
    bmorgil,
    I can’t a response back from Champion and found another company in Chicago called Engineered Cooling Products and sent them my diagram and the guy emailed me back in 10 minutes. I’m debating on whether I should put a electric fan or not.
    Your thoughts, I’m leaving the original finger slicer off so I’m thinking I should put some type on it.

  8. #8
    Senior Member bmorgil's Avatar
    Join Date
    Dec 2018
    Location
    Northwestern Ohio
    Posts
    350
    TJ for sure it will need some kind of fan. My son has great success with his monster Jeep and a "Pusher" fan. It is mounted on the outside of the radiator and pushes the air through. This was required because there was no room at all between the motor and the radiator. It runs very cool even when muding hard. I ran a S10 V8 drag car in the 80's. It had a twin fan setup on the inside of a large Griffen radiator. The two fans ran independently on thermal switches. One came on at 160 and the other came on at 190.

    Keeping in mind that a lot of modern vehicles rely solely on electric fans, it is very nice to have the fans run for a bit after shut down.

    I am a "FAN" of the electrics! For sure the best way to go in MHO. There are some nice fans with shroud packages out there.

  9. #9
    Senior Member TJones's Avatar
    Join Date
    Apr 2018
    Location
    Akron, Ohio
    Posts
    232
    bmorgil the guy doing my motor told me for sure mount the fan on the outside pushing in. I do have the room but Chuck for sure said to mount it outside so it pushes towards the motor.
    We’ll see if anyone gets back to me and then it’s off to Summit Racing, I’m so glad they are only 2 miles from my shop Kinda handy but kinda expensive some times bc they are so handy and close!!!

  10. #10
    Senior Member bmorgil's Avatar
    Join Date
    Dec 2018
    Location
    Northwestern Ohio
    Posts
    350
    It's no better here in Toledo. They deliver the next day!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •