Page 2 of 5 FirstFirst 1234 ... LastLast
Results 11 to 20 of 42

Thread: Another Heep project

  1. #11
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    3,570
    Ran out of daylight for today. I did get the driver's side frame all welded up and reinforced. Then repaired the rear crossmember using some 1/4" cold rolled. This should add a bit of strength to the rear bumper.
    Attached Images Attached Images

  2. #12
    Super Moderator LarrBeard's Avatar
    Join Date
    Nov 2014
    Location
    Ft. Wayne, IN
    Posts
    2,482
    You and your little welder and hammer do nice work!

  3. #13
    Super Moderator bmorgil's Avatar
    Join Date
    Dec 2018
    Location
    Northwestern Ohio
    Posts
    3,558
    Looking good! You are moving fast! That thing's back in action soon.

  4. #14
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    3,570
    Thank you guys. Maybe I can keep the momentum rolling on my own project.... After at least getting the roof done on the garage extension.

  5. #15
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    3,570
    In between putting the turkey and ham in the oven, I did get a bit more paint removed on the frame. There was a lot of scale on the driver's side shock tower. It all came out fairly clean. The axle snubber was rotten, and one bolt is ate off flush with the frame. I did drop the skid plate down, cleaned, and painted the center frame rails to prep for the skid plate reinforcement pieces to be installed.
    Attached Images Attached Images

  6. #16
    Super Moderator bmorgil's Avatar
    Join Date
    Dec 2018
    Location
    Northwestern Ohio
    Posts
    3,558
    It is coming back!

    What do you use for a face mask so you can breath while the dust is flying? Everything I try fog's my safety glasses.

  7. #17
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    3,570
    A 3M dust mask with the replaceable filters. My prescription glasses sit on top of the nose piece alright, but does move the byfocal up a bit. It just takes some getting used to.

    Today, the right frame rails was tackled, and the right front stifner.
    Attached Images Attached Images

  8. #18
    Senior Member 5JeepsAz's Avatar
    Join Date
    Aug 2019
    Posts
    577
    Great progress! Ton of rust on what you removed. Looks like new

  9. #19
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    3,570
    Today it was too windy for outdoor welding, so I brought in some parts to fix. The skid plate/crossmember needed the self tapping screw holes filled, and the center mount holes repaired. Then it was time to install the skid plate. Thankfully all the measurements were pretty good and bolts lined up.
    The next order of business was the fuel tank skid plate. This was in sad shape. With a new piece being $200., and the owner will never take this rig off road, it will last forever with a simple patching.
    Attached Images Attached Images

  10. #20
    Super Moderator LarrBeard's Avatar
    Join Date
    Nov 2014
    Location
    Ft. Wayne, IN
    Posts
    2,482
    Dern, you do nice work!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •