Results 1 to 10 of 10

Thread: New Member Intro. 64-68 Wagoneer

  1. #1
    Junior Member
    Join Date
    Jul 2020
    Location
    Spokane, WA
    Posts
    3

    Cool New Member Intro. 64-68 Wagoneer

    Good Morning Everyone,

    I would like to introduce myself and my project I picked up about 2 months ago. It has been a while since I have been on a forum, so bear with me while I remember how to use them.

    I found a 1964-1968 (unsure of the year, but through significant amount of digging I have narrowed it down to somewhere in that ballpark with me leaning towards the earlier years) Jeep Wagoneer as a project to keep busy during these strange times, with a plan to turn it into an offroad play toy.

    It was in rough shape to say the least, but started right up and I picked it up for what I feel is one heck of a deal. After a short tow to my place, the fun began. I will attach a handful of photos below that show its condition when purchased. Hopefully someone who is a bit more knowledgeable about the older FSJ's can help me to sort out what year I have. The seller thought it was a 1967, the title says 1970 (it was an abandoned vehicle when she got it) and the front end says 1964-1965 if I am correct.

    20200602_175249.jpg

    20200602_175302.jpg

    20200602_175232.jpg

    20200603_203811.jpg20200603_203811.jpg

    Looking forward to getting my build thread up and going and seeing progress of not only my project, but everyone elses!

  2. #2
    Super Moderator bmorgil's Avatar
    Join Date
    Dec 2018
    Location
    Northwestern Ohio
    Posts
    3,558
    Welcome! It looks like you have a project there. There seems to be a lot of original parts. The body looks fairly straight. For sitting it still looks like it has some floor in it. This will be a great rebuild to watch. In the 1960's my dad used to bring these home on occasion for testing of the drive lines. They went everywhere in the snow!

  3. #3
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    3,570
    Welcome back sWagoneer!

    All I can say is I like it. The floors don't look all that terrible, just soft with a few through holes. I recognize the steering wheel and the hanging pedals from the ones that were repurposed in my '63 wagon.

    We look forward to following your progress!
    Attached Images Attached Images

  4. #4
    Junior Member
    Join Date
    Jul 2020
    Location
    Spokane, WA
    Posts
    3
    Quote Originally Posted by bmorgil View Post
    Welcome! It looks like you have a project there. There seems to be a lot of original parts. The body looks fairly straight. For sitting it still looks like it has some floor in it. This will be a great rebuild to watch. In the 1960's my dad used to bring these home on occasion for testing of the drive lines. They went everywhere in the snow!
    I was pretty shocked, almost all of the interior odds and ends are there, rear seat I am going to have re-done, I fell in love with it. Body is in decent shape, owner before me had a plow on it and destroyed the front bumper and cut out quite a bit of the sheet metal on the front to make it fit. I guess I will have to build a cool offroad bumper haha. It took me quite a while to get the floors completed that was the biggest challenge thus far. Mostly because I have zero experience with a flux core welder. But by the time I was just about finished I got the welds down. Here is the floor I built!

    20200717_154943.jpg20200717_154943.jpg

  5. #5
    Super Moderator bmorgil's Avatar
    Join Date
    Dec 2018
    Location
    Northwestern Ohio
    Posts
    3,558
    Just like new man! You should try your hand at rebuilding the chopped up front from the plow. We have seen gmwillys recreate frame rails!

  6. #6
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    3,570
    You have my stamp of approval. I've gotten so used to running argon with my MIG, that it would probably look like a mud dobber crapped on the seams. Good job!

  7. #7
    Junior Member
    Join Date
    Jul 2020
    Location
    Spokane, WA
    Posts
    3
    Thank you guys! I definitely plan on giving the front end a shot, that will definitely be a first, but honestly most of this is a first for me haha.

  8. #8
    Senior Member 5JeepsAz's Avatar
    Join Date
    Aug 2019
    Posts
    577
    Great project! Do you have a pic of the front? The numbers on these thing, engine, rear diff tag, regular old serial number on the door jam can help age it more closely. They pirated lots of front grilles if you have or had the rhino. Also, the back lights, the reverse light may not have been on early ones. More pics!

  9. #9
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    3,570
    The biggest thing with welding sheet metal is patience. Too much heat in one location causes you headaches. Stick and move until all your tacks are filled in. Find you a scrap piece of copper, and use it as a backer plate. This will help dissipate heat, and will help if your joints are not exact.

  10. #10
    Senior Member
    Join Date
    Nov 2019
    Location
    Oklahoma
    Posts
    447
    You've done some good work to start out there!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •