Page 3 of 39 FirstFirst 1234513 ... LastLast
Results 21 to 30 of 384

Thread: 1st Time Jeep Owner

  1. #21
    Senior Member
    Join Date
    Jun 2021
    Posts
    190
    I tend to agree with bmorgil that it looks like the PTO control. I'm not familiar at all with the Tuxedo Park rigs, but my CJ has the PTO control on the center floor just behind the transmission gear shift and just in front of the seats. I could see them moving a control lever up on the dash for more convenience, but who knows?

  2. #22
    Senior Member
    Join Date
    Jan 2022
    Posts
    192
    I think this is an original key. It says Briggs & Stratton on the other side.
    IMG_1069.jpg

  3. #23
    Super Moderator LarrBeard's Avatar
    Join Date
    Nov 2014
    Location
    Ft. Wayne, IN
    Posts
    2,551
    Mine just says B&S...

  4. #24
    Senior Member
    Join Date
    Jan 2015
    Location
    E OK
    Posts
    484
    You might find there isn’t any insulation on the wires with the mice in it that bad. I don’t know what’s in the insulation they like so much but mice are pretty effective at stripping wire.
    Last edited by 51 CJ3; 01-14-2022 at 09:21 PM.
    Jeff
    '51 CJ3A
    '47 CJ2A

  5. #25
    Super Moderator bmorgil's Avatar
    Join Date
    Dec 2018
    Location
    Northwestern Ohio
    Posts
    3,806
    There is seldom a glove box manual. You will usually have to purchase a reprint. KW has them.

  6. #26
    Senior Member
    Join Date
    Jan 2022
    Posts
    192
    Checking the points and decided to install new points and condenser. It appears the only way to remove the points is to remove the entire plate inside distributor. IMG_1221.jpg

  7. #27
    Senior Member
    Join Date
    Jan 2015
    Location
    E OK
    Posts
    484
    That’s a nice looking distributor. Points are a bit worn. Mine was rusty and packed full of sand. I couldn’t believe it was still making spark.
    Jeff
    '51 CJ3A
    '47 CJ2A

  8. #28
    Senior Member
    Join Date
    Jan 2022
    Posts
    192
    I've drained the oil and replaced the filter. Disconnected the fuel line, hooked up a fresh battery and started checking "what works and what doesn't". Amazing almost everything works, headlights (high and low beam), all of the parking lights, dash lights, even the fuel gauge. Remember this thing has been sitting since 1985! The engine turns over easy however even with a couple shots of carb cleaner directly into the carb, not even an attempt to start. Also noticed while turning engine over the vacuum wipers both work. Anyway, came to the conclusion "no spark" which lead to checking the points. Points appear very worn so I figured to simply replace both the points and condenser. Never worked on one of these engines, does it require removing the points plate to replace points?

  9. #29
    Super Moderator bmorgil's Avatar
    Join Date
    Dec 2018
    Location
    Northwestern Ohio
    Posts
    3,806
    No, just remove the screws and remove the points and condenser.

  10. #30
    Senior Member
    Join Date
    Jan 2022
    Posts
    192
    I took out the screw near distributor center shaft as well as the on that's used for adjusting point gap however Screw "A" attaches the wires cannot be accessed without removing the plate. It appears screws marked "B" need to be removed to take the points plate out and allow access to remove screw "A". dist.jpg

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •