Results 1 to 9 of 9

Thread: Need advice : Vent lines for the Air Cleaner on M38

  1. #1
    Junior Member
    Join Date
    Oct 2024
    Posts
    4

    Need advice : Vent lines for the Air Cleaner on M38

    Hey guys, New Jeep owner as of last week. An M38. I'm trying to fix some "loose ends" and need some help. So....

    1. My Air Cleaner just has 2 holes in it ( nothing going into it). I put a nipple on one hole and attached the Windshield wiper line to it. I have no vent line coming from the gas tank but plan to run one to the air cleaner. Does that start out as a hard line and then goes to a rubber line? Or is it a hard line all the way to the air cleaner? Also, I have no vent line from my master cylinder so I assume I have an after market ( it also has the large 15/16 inch nut). Should I have a vent line for it? Right now I plan to just have a line from the windshield wipers and one from the gas tank go to the air cleaner. Does this make sense? Also, I do not see a vent line for the transfer case neither.

    Thanks for any help.

    Randy B

    ps... more questions to come....

  2. #2
    Super Moderator LarrBeard's Avatar
    Join Date
    Nov 2014
    Location
    Ft. Wayne, IN
    Posts
    2,562
    RandyBee:

    Welcome to the forum.

    Your M38 had a fairly complex fording system of lines and vents that went to the gas tank, brake cylinder, differential, probably the ignition coil. the air cleaner and probably several other places I've missed. It was controlled by a fording valve.

    I would suggest that you get a copy of the M38 tech manual to see the whole layout of the fording system. (is it an M38A1?)

    Here is a link that describes the M38 fording system in detail.

    https://cj3a.info/sibling/m38vent/vent.htm

    And keep the questions coming!
    Last edited by LarrBeard; 11-02-2024 at 07:53 AM. Reason: Added link to fording system

  3. #3
    Super Moderator bmorgil's Avatar
    Join Date
    Dec 2018
    Location
    Northwestern Ohio
    Posts
    3,839
    Welcome RandyBee!

    LarrBeard has you on the right track. Here is a link to the Tech section of this forum for the Engine/Clutch Military manuals on your M38. I think Chapter 6 briefly discusses the Fording System.

    https://willysjeepforum.kaiserwillys...lity-Truck-M38

    There are 3 or 4 manuals in the Tech Section for your Jeep. Keep the questions coming! gmwillys and LarrBeard have helped a few through the Military versions.

  4. #4
    Junior Member
    Join Date
    Oct 2024
    Posts
    4
    Thanks Guys, I have all 5 manuals. I haven't seen a good description (yet) of the vacuum lines/vent lines. Still trying to digest all this new info. I find it a little odd that there is a vent line for the MC. Fording or no fording I don't understand why. Everyday cars/trucks do not have vented MC systems.
    Randy
    Last edited by Randybee1; 11-02-2024 at 11:34 AM.

  5. #5
    Super Moderator bmorgil's Avatar
    Join Date
    Dec 2018
    Location
    Northwestern Ohio
    Posts
    3,839
    I think you will find the link LarrBeard posted is as good as you will find. The Master Cylinder is vented and could take on water if submerged.

  6. #6
    Junior Member
    Join Date
    Oct 2024
    Posts
    4
    bmorgil, you're right .... Thank you LarrBeard, very good info!!!

    I still do not understand the theory behind venting the master cylinder. Its a sealed system anyway so why add a venting system to it?

  7. #7
    Super Moderator bmorgil's Avatar
    Join Date
    Dec 2018
    Location
    Northwestern Ohio
    Posts
    3,839
    The cap of the master cylinder is vented so as the volume of fluid decreases in the master cylinder as the pads/shoes activate, wear, and fluid temperature changes, changing the level in the reservoir, there is a vent to equalize the pressure.
    Last edited by bmorgil; 11-04-2024 at 08:47 AM.

  8. #8
    Super Moderator gmwillys's Avatar
    Join Date
    Aug 2017
    Location
    Alabama
    Posts
    3,787
    Welcome Randybee1

    I'm a little late to the party, but here is one of the best diagrams that I had in my archive of nearly worthless knowledge:

    http://willysmjeeps.com/downloads/M3...stem.12.04.pdf

  9. #9
    Junior Member
    Join Date
    Oct 2024
    Posts
    4
    Thanks gmwillys! Excellent info.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •